Dripka sub zero how to figure out how much the original costs

Every vaping enthusiast should know how to disassemble an electronic cigarette and clean it from carbon deposits. This operation should be carried out periodically to maximize the life of the device. An important factor is the correct use of cigarettes. Despite the diversity of the model range of devices, it is possible to identify general principles of their maintenance, because the devices consist of identical functional blocks. To disassemble them yourself, you do not need any special tools.

How to disassemble a cigarette

An electronic cigarette is not that difficult to disassemble. For complete disassembly you will need:

• tweezers;
• plastic tube;
• hammer;
• pliers;
• thin drill;
• soldering iron;
• needle.

All vaping devices are designed in a similar way, which is why they are disassembled in the same way. Roughly speaking, they consist of three main parts: battery, evaporator, clearomizer (cartridge for solution). The main thing is to know what is where.

Next, disassemble the electronic cigarette step by step:

Use thin tweezers to disconnect the main contact, unsolder the wire, and unfasten the cartridge.

Then you need to separate the battery from the atomizer. To do this, grab the battery with one hand and the evaporator with the other.

And smoothly, carefully bend and unbend the device at the junction. It is important to calculate the force here. If you don’t press enough, nothing will work; if you overdo it, you can break it. This must be done until a noticeable gap appears.

Next we disassemble the body

This must be done just as carefully. When the thread is visible during the process of unbending, you need to place a tube (it should be of a smaller diameter) on the side of the cartridge and literally knock out all the contents by tapping with a hammer.

There is a plastic washer at the bottom. It should be removed and all wires separated. If they are glued, then you will have to separate them with pliers, protect the gluing points with a needle, and clean the holes with a drill from any remaining glue.

Then remove the circles, unwind the tape and remove the bridge.

Then you need to remove the spiral by pushing the wires connecting the battery. If the coil is in poor condition, you need to remove it with tweezers from the clearomizer side.

The battery usually appears to be a one-piece design, but it can also be disassembled.

Models of e-cigarettes designed similarly are disassembled in the same way. But for the first time it is better to ask someone to show all the stages of disassembly.

The main thing in this process is not to overdo it. The device is durable, but not that strong and can be easily damaged.

Required Tools

To disassemble the device and then reassemble it during repairs or periodic inspections, you will need the following tools:

• small tweezers;
• pliers, screwdriver;
• needle, knife;
• the drill is thin;
• small rubber mallet;
• plastic tube;
• soldering iron

The diameter of the tube should be smaller than that of the ES.

Modern high-tech versions of electronic cigarettes are far from conventional cigarettes in appearance and allow you to control even such a parameter as the temperature of the inhaled vapor. During maintenance work, it is good to have a diagram of the product to take into account all the nuances of the model.

How to disassemble the Eleaf Ijust

This question is asked by almost all users of this device who have encountered the above problems. Such a device is easy to disassemble, which vapers themselves can do. If the button in the Ijust gets stuck, you must adhere to the following algorithms:

• remove the rubber band connecting the cartridge and the power source;
• By twisting or bending the connection of these parts, slowly stretch them away from each other. This process is monotonous and slow. Do not make sudden movements so as not to pull out the part. This is how you can break an e-cigarette;
• pull out the connector that secures the battery pack and atomizer;
• unscrew the evaporator;
• Now having access to the battery pack, perform repairs on it.

Management

First, the device is disassembled into separate functional blocks. The atomizer unscrews from the battery pack. If you have to deal with a vape that contains a cartomizer, use tweezers to pull out a special contact that holds the reservoir for filling with liquid.

Next, the internal “filling” of the battery pack is released. For these purposes, a plastic tube is used. The latter is inserted into the lumen of the electronic cigarette body. Next, pressure is applied, due to which the batteries are removed. The plastic washer is removed, which can be seen at the bottom of the battery.

The next step involves disconnecting the wires. The conductors can be soldered together. In such a situation, pliers are used. The tool disconnects the wire contacts and removes the glue.

There may be a heavy accumulation of dirt on the surface of the battery. To clean the functional block, use a drill. Using the tool, existing blockages are carefully removed.

Then the metal tape rings, which can be seen at the bottom of the battery, are disconnected. The material unwinds, releasing the battery bridge. All that remains is to remove the spiral presented in the design. For these purposes, the sealing foam is removed. You can cope with the operation using tweezers. The spiral is removed by pushing the wires in the direction away from the energy storage device.

As you can see, there is nothing difficult in disassembling the battery. During the work process, the main thing is not to overdo it. After all, careless actions can lead to irreversible consequences, when the only thing left to do is to send the battery for scrap.

The main reasons for disassembly

Cleaning and disassembling the iGast s electronic cigarette for spare parts is necessary in the following cases:

1. With prolonged and regular use of the device. With prolonged use, a coating appears inside, which consists of decay products of the ijust flavors used, tar and nicotine;
2. If liquid leaks;
3. When changing or updating the fluid. The container for liquids must be cleaned after 7 charges;
4. Gurgling, squeaking or whistling sounds when taking puffs;
5. Liquid leakage;
6. Steam stopped being generated;
7. Noticeable changes in smoke pressure during use;
8. Burnt taste in the mouth or strong odors during use;
9. The saturation and density of smoke has noticeably decreased;
10. Errors in ijust s firmware

Don't wait for any of the signs and causes to appear. It is best to carry out a preventive inspection and cleaning of the device once or twice a week, studying the instructions and problems of the device. And in case of deviations from the operating condition, it is necessary to quickly disassemble the device and remove dirt.

What if you feel something burning?

When the smell of burnt cotton wool and paper appears during vaping, and the liquid acquires a bitter taste, service is necessary. You can return the previous flavor with your own hands by replacing key components.

With prolonged and active vaping, the cotton wool burns out, and a coating forms on the coil. This deforms the coating and adds an unpleasant burning sensation to the steam. The spiral, like the wick, on the atomizer is changed manually. The main thing before doing this is not to make a mistake with the material and winding option, which are designed for different voltages.

If the problem is not resolved, the vaporizer for the electronic cigarette has failed and needs to be replaced.

Proper replacement of cotton wool is a matter of patience. Before the first puff, the wick is moistened with liquid and left for 5-10 minutes. This will allow the cotton wool to soak and not burn out when current is applied.

Causes of breakdowns and malfunctions of the Eleaf Ijust

Here are the most likely causes of e-cigarette failure:

Low quality, defective. You can fix a breakdown even without experience. We are talking about nameless devices. Due to the increased demand for such gadgets, the number of counterfeits is growing rapidly. They come to us from China, where we do not have the opportunity to control their assembly and the quality of spare parts. A distinctive feature is that the cost is approximately 2 times less than the original. Sudden changes in pressure. All vaping devices do not like pressure changes. Therefore, such problems in the operation of the device are also observed. This is especially true on an airplane. This situation can be solved by placing the device in a vertical position. In this way, spillage of the steaming liquid can be prevented. Formation of condensation. The steam generated by the atomizer has a higher temperature compared to the tip itself, through which it passes into the lungs of the steamer. To avoid leakage, condensation must be avoided. After disassembling the device according to the instructions described above, blow out or wash the evaporator. Low quality vape liquid

It is very important to use only high-quality factory-made smoking mixtures. Low-quality batches spoil the “filling” of electronic devices and are dangerous to the health of the steamer

In addition, the factory mixture has the necessary consistency, which will allow it not to leak. Good quality liquid does not contain any impurities that can give an unpleasant taste and aroma. Poor build. Leaks in the threads may occur due to loosely tightened atomizer components. This problem can be solved by tightening all spare parts and checking the tightness of the connection. However, this does not mean that it is necessary to tighten it too tightly. This could cause your device to fail completely. Temperature changes. E-cigarette leaks can occur due to high temperatures or sudden surges. For example, when vaping outdoors in winter you will not feel this, but indoors the atomizer will begin to leak. To eliminate this problem, experienced vapers do not advise vaping for about 15 minutes after going outside in the cold. In a heated room, place the device on a horizontal surface and wait until it reaches the same temperature (about 20 minutes). Be careful with electronics in the summer too. In hot weather, when the device is exposed to direct sunlight for a long time, the liquid becomes very hot and can leak out.

Vape design

Electronic cigarettes are a modern alternative to conventional tobacco products. They are called differently, but the essence does not change. The device is designed to convert a special liquid containing flavorings and often nicotine into a vapor state. Next, the smoker inhales aromatic vapor instead of regular tobacco smoke.

Products are divided according to their functionality into the following types:

• box mods (contain a control board and control system);
• mechanical mods (do not have an electronic system).

Devices are also divided by size and type of atom.

There is a wide range of e-cigarettes on the market. The leading positions are occupied by products of the following brands: Armango, Eleaf, Joyetech, Kangertech and others. Regardless of the brand, mods consist of the following components:

• battery pack (can be mechanical or automatic type);
• cartridge (storage) for liquid;
• electric evaporator (atomizer);
• Some models have additional parts that control the supply of aromatic liquid.

Atomizers are small cylindrical containers with an evaporation system inside, responsible for converting liquid into vapor. They consist of a spiral (nichrome, canthal, steel) wound around a wick and a contact group. Steam generators vary in coil thickness.

The wick is placed in a special bowl (ceramic), which has holes for contacts and for air. It is covered on top, protecting it from damage, by a bridge through which the smoking liquid is supplied. The bridge with the bowl is wrapped in metal sponge. Thanks to the latter, liquid is transferred from the cartridge to the steam generator. When puffing occurs, vaporization begins.

Specifications

This device has the following technical features:

• diameter - 25 mm;
• height - 96 mm;
• petal contact order;
• replaceable drain;
• safety if the battery is installed incorrectly;
• hybrid connector;
• extensive openings for air removal;
• short circuit protection;
• button lock.

All these characteristics ensure the reliability of the device.

The button in it is designed quite interestingly - it has a spring that does not take part in the transmission of current.

Its functions are reduced to pressing at the right moment a plate consisting of 4 petals to a sharp pin, as well as to the body of the drip atomizer. These factors significantly reduce drawdown.

Why should you be careful with glass?

Glass is the most vulnerable element of a vape device. Owners of rare electronic devices ordered from AliExpress or other foreign resources can verify this. It is difficult to find components for new devices in stationary vape shops.

Cracked glass cannot be repaired. Moreover, with frequent unscrewing and tightening, the crack will spread.

To avoid spending money on buying a new vape, it is wise to clean your electronic cigarette after every second or third refill.

Blocking the atomizer tank is a typical problem for both cheap and branded vapes. If the atomizer tank does not unscrew, this is due to several factors.

Firstly, everyone tries to tighten the device as tightly as possible to prevent fluid leakage. Secondly, during operation, the design of the vape is deformed, and a coating forms on the threads, which impairs the rotation of parts.

How to get to the button and change it

In order to get to the button of the electronic cigarette, you must:

1. Remove the rubber part of the electronic cigarette;
2. Rotate the junction of the battery and the container with liquid;
3. Pull out the connection connector;
4. Twist the evaporator;
5. Remove the board and electronics;
6. Get to the button and fix problems associated with it.

It is important to do all this on a flat, clean surface, as there are common cases when some of the components and devices are simply lost

How to properly disassemble an atomizer?

In order to correctly and without consequences disassemble the atomizer of an electronic cigarette, you must perform the following steps:

1. In order to separate the inner component of the cigarette from the outer body, it is necessary to roll the steam generator on a hard surface, slightly pressing it on top;
2. After this, you need to pick up the top edge of the cigarette and remove the contents. If the tenacity is poor, you need to use tools;
3. Next, you need to use a screwdriver and carefully separate the top plates, and then pull out the wick;
4. The last step is cleaning the atomizer. After this, you need to repeat the sequence in reverse order to assemble the cigarette.

An important point: this work must be done carefully, since the steam generator contains a lot of small parts and components that can be lost when disassembling the electronic cigarette.

Conclusion

Thanks to its relatively simple design, anyone can take the ijust s apart and put it all back together. In this case, it is necessary to act and carry out all procedures carefully, without any sudden movements or pressure.

In order not to disassemble or repair ijust s too often, you need to remember about preventive measures, the main one of which is to use only high-quality fluid. Using poor quality fluid may cause your ijust s to malfunction.

Battery faults

The battery is the heart of the electronic cigarette and requires especially careful handling. Devices intended for beginners (eGo format cigarettes and some higher-end models) use different degrees of protection against breakdowns: from overcharging, overdischarging, short circuit, which can lead to the vape exploding, etc.

Unlike mechanical mods, you won't be able to cause the power supply to explode, but less serious malfunctions are still possible.

Some breakdowns are associated with violation of the rules for using lithium-ion batteries in general:

• the battery discharges quickly;
• the battery does not charge;
• The battery does not supply current to the evaporator when the fire button is pressed, although there is a charge.

The solution is to replace the cell if it is replaceable (you can buy a new 18650 battery at any vape shop for 600–800 rubles), or throw away the cigarette if replacement is not provided.

The cigarette (if it is not a mechanical mod) reports about repairable battery failures using an indication - either a message on the LED screen or blinking LED. If the vape blinks and does not work, the breakdown may be caused by:

Short circuit - occurs when the battery contact is shorted to the cigarette body. The solution is to bend the terminal and screw the evaporator not all the way. To definitely get rid of the problem, the contact needs to be isolated - for this it is better to send the ES to a service center.

Evaporator resistance too low. The solution is to replace the spiral.

No contact with the evaporator. The solution is to tighten the latter more tightly and check its terminals. In eGo format cigarettes, it is also possible for the central contact to be pressed, which occurs when the clearomizer or charger is screwed too tightly to the battery

To fix this, the contact must be pryed with a needle and carefully lifted. Contamination of contacts, due to which current conductivity deteriorates. The solution is to clean the terminals with alcohol.

You cannot wash a cigarette with water - if water gets inside the case, the electronic circuits on the board will burn out.

If your new e-cigarette does not work and blinks frequently, it needs to be charged.

Cutoff. The battery automatically switches off if the puff is too long to prevent the coil from overheating. To avoid this, you should not puff for more than 10-15 seconds.

The indicator may behave differently depending on the model of the electronic cigarette: the number of blinks may be different, and sometimes the color of the backlight may change. Details about the types of signals of a particular model can be found in the instructions for it.

Device design

The Subziro drip atomizer is an excellent combination of an unusual and interesting design, as well as high technical characteristics. They make using the device very convenient. It is created in such a way that it is perfect for both avid vapers and newcomers to the world of vaping.

This device is available in several colors - red, pink, blue, grey, black and copper. Its appearance is distinguished by grace and severity, but at the same time it is pleasantly pleasing to the eye. Its metal, slightly rough surface is decorated only with engraving of the company logo, and each engraving line is made perfectly clear.

The packaging is made in the same style as the device itself; on the reverse side there is information about the technical characteristics of the device, its features and precautions for use. Inside each package there is a steel originality card with a serial number.

Finally

Yes, it’s not easy for beginners with atomizers - it always seems like your hands are growing from the wrong place and you’re doing everything wrong. Don't be discouraged, because this is just the beginning.

All atomizers have almost the same structure and principle of operation, so, having figured out your first one, you have, in fact, learned how to deal with any other. Try, treat your gadget with respect and, believe me, it will repay you in kind - the clouds of steam will become richer and tastier.

What do you think about this? Have you had any experience disassembling your own device? Share your story with us.

Most smokers who switched from cigarettes to vaping try drip. It has many advantages and is easy to use. Beginners in this business often have difficulties in using it. Instead of the expected aromatic steam, you get bitterness. The dripper is flowing or spitting. What are the reasons for the device malfunction? Let's talk about this in this article.

Unusual device base

The unusualness of the Subziro drip atomizer base lies in several features. The first of them is a kind of installation. It is installed into the case from above, and you need to carefully ensure that all the airflow holes coincide with the air vents. The second feature is that the base does not move freely along the body, but rests against the airflow adjustment and remains in a fixed position. This sets Subziro apart from other drippers. In this position, the base does not touch the mod, so heat transfer into it is reduced to a minimum.

To install the spirals, racks with holes are provided in which massive windings are pressed with hexagonal screws. Wide air outlets provide good draft and intense steam generation. The third feature is the disassembly of the base and the possibility of washing it. The package includes special equipment for comfortable disassembly and assembly of the device.

Cleaning methods

Before you start cleaning the coil, you should prepare it for this procedure. To do this, the body of the mod is disassembled and all the cotton wool is removed from the winding.

Cotton wool should not be stored; it is better to throw away the used one after removing it and prepare the required amount of new one in advance.

It follows that after cleaning it will be necessary to add smoking liquid so that the cotton wool is not overdried.

The winding cleaning method should be chosen based on the degree of contamination. The easiest to put into practice and more effective tips:

All cotton wool is completely removed from the spiral, the spiral heats up quite strongly and is immediately lowered into a container of water. To warm up the coil means to bring it to an orange color. When using this method, you should be careful, since immersing a hot coil in water can cause a burn. After cleaning, it is recommended to use new cotton wool.

The spiral is burned to the maximum possible temperature, all the fumes are burned, and it is recommended to clean off its remains with a hard brush. It is not recommended to grab the spiral with bare hands during the firing process and for some time after.

The principle of operation is similar to previous methods, the winding is heated and placed under a stream of cold water, some of the carbon deposits come off under water, what remains is cleaned off with your hands or carefully pryed off with tweezers.

Sedum acid. The spiral is heated and briefly immersed in a solution of orthophosphoric acid

There is no soot left behind, but afterward it is important to thoroughly rinse the coil with water, since the remaining acid vapors can lead to poisoning. This method can also damage the integrity of the material from which the spiral is made.

How to disassemble an atomizer

Let's look at how to “dismember” an atomizer for cleaning using the eGo-T device as an example.

First you need to separate the insides of the atomizer from its body. You won’t be able to figure it out so easily the first time, but you have to try. To do this, sometimes it is enough to roll it several times on a hard surface, pressing it on top, for example, with plywood. Then, hooking it by the top edge, remove the insides. Remove the rubber sealing ring and separate the top plate. This is done using a screwdriver. There is a wick inside. In order not to cause harm, when removing it, you need to push, not pull. After this, the atomizer can be washed and cleaned.

In other models, the evaporator design may differ, but, in principle, all atomizers are designed similarly. They have a body, seals and what actually allows the liquid to evaporate, that is, a heating element.

The main thing is that disassembly must be carried out extremely carefully. This concerns the atomizer primarily due to the abundance of small parts.

Before you begin disassembling, it is important to know your e-cigarette well. That is, imagine where and what it has and what it is called, so as not to confuse the battery with an atomizer

And so as not to try to tear off something that cannot be disassembled.

No Atomizer

When you press the power button, steam generation does not occur, and the display shows “No Atomizer”. The system reports the absence of an evaporation system while you installed the atomizer, but the box mod does not see it. Often this problem occurs if the replacement evaporator (if you have a clearomizer) is not screwed tightly into the base. Owners of drip caps and serviced atomizers can safely check how tightly the screws in the stands are tightened

If checking the evaporator element did not help, then pay attention to the pin connector. Perhaps the central pin does not reach the contact in the recess of the power supply platform

It is worth noting that this kind of problem can also arise due to too low resistance of the spiral. Make sure the coil resistance is not lower than what your mod supports. If the resistance matches, a problem may occur, causing a short circuit if the coil touches the dome structure, or the walls of the tank.

We recommend that you familiarize yourself with models with an adjustable pin, as well as spacious bases for comfortable installation of heating elements:

Kylin Mini RTA atomizer

– a productive tank, which is one of the best products presented by Vandy Vape. The atomizer is equipped with several glasses of different capacities, is made in an original design, and is capable of producing a large amount of tasty vapor.

Atomizer CoilArt Azeroth RDTA

is one of the best solutions on the market. The device has an interesting design, and the RDTA format guarantees simple placement of cotton wool and a bright taste sensation from vaping. The set for the tank includes three drip tips, among which you can choose the option to suit your vaping style! The serviced device will look harmonious on various fashions.

In electronic cigarettes without a display, the system notifies the user of such a problem by flashing the indicator repeatedly when pressing the power button.

Instructions for unscrewing the tank

If the tank does not unscrew, then the problem is solved by performing the following manipulations:

1. Stop the base without applying any force, as the glass may crack and will not be suitable for further use. Make this with some thin object that will fit into the air vent. This way you will fix the body;
2. Using rubber gloves or a thin rubber mat, unscrew the evaporator, glass or drip tip so that your fingers do not roll over the body of the device;
3. Wrap the glass in a couple of layers with electrical tape or adhesive tape so that the glass is not deformed with pliers if you are unable to remove the clearomizer by hand;
4. Use a wet cloth/thin stream from the tap to rinse the joints and clean the threads. If there are no liquid residues on the fasteners, then everything was done correctly. It is better not to refuel the e-cigar while unwinding the tank;
5. Unscrew the remaining parts and wash them thoroughly;
6. Install the glass several times, clean parts will not leak.