How to open a SIM card on an iPhone without a key. how to remove sim card from iphone

Damaged SIM card contacts

If the gadget does not connect to the network, try the following:

remove the card holder;
visually inspect them for dirt and damage;
shine a flashlight into the socket, make sure there is nothing unnecessary there, blow it out;
Wipe the tray and SIM card so that the golden chip is perfectly clean;
insert the card back into the device and start it.

Read about operators: Why the phone does not see the SIM card and what to do in such a situation

Often this simple operation helps to revive old SIM cards of Beeline and other operators, after which the gadget can see them again.

The problem may be caused by user actions or may not be related to the handling rules. It is not necessary to find out why the SIM card stopped working normally. Operators replace an old SIM card with a new one for free, and regardless of the reason for its breakdown, loss, or other situation. Only Beeline has a paid replacement - 30 rubles, and if the old SIM card does not support 4G, the operator will return the replacement cost with bonuses.

To obtain a duplicate SIM card, you must contact your operator with an application. To do this, just come to any of the operator’s offices, or order delivery.

It is worth considering that delivery is not free, and depends on the period, city, and time of order. You can get a card in a store whenever you need it, and it won’t take much of the subscriber’s time. It usually takes a few minutes to receive a duplicate.

There are many reasons why your phone does not recognize the SIM card. We will describe at least 11. Surely, among these solutions you will find the answer to why your smartphone stopped reading the SIM card at the most inopportune moment.

If your iPhone does not see the SIM, the problem is either with the phone or with the SIM card. In the first case, you may need the help of a service engineer or your accuracy. And in the second - replacing the SIM card with the operator or calling the support service.

Expiration date of the SIM card. If you do not use the SIM card for a long time, it is automatically blocked. Blocking may occur due to a negative balance. Check the blocking conditions with your operator. Helpline numbers are listed below.
Features of activation. With some operators, you can activate a SIM card only after you complete the first paid action.
Incorrect “transformation” of a SIM card into mini-SIM, micro-SIM, nano-SIM. The phone does not see the SIM card when the owner cuts it himself and damages the contacts. Entrust this process to specialized service centers or purchase microSIM SIM cards from any operator on our website.
The card is damaged. The SIM card may also fail. For example, if you carry it in your pocket or insert/remove it from your phone too often.

The SIM card has contacts:

Vcc – power supply;
Reset – control;
Cloc – clock frequency;
Vpp – for recording information;
I/O – input/output;
General (“ground”).

Damage to any contact leads to failure. You will have to apply for a new SIM.

If there is contamination, use the following cleaning methods:

eraser - gently rub the Sim contacts with a regular eraser;
alcohol - with a slightly moistened disk, wipe the SIM card on all sides.

You cannot wash it in water or with cleaning products, as such actions will damage it. If cleaning does not produce results, replace the Sim with a new one.

Before diagnosing, you need to familiarize yourself with the main reasons why the phone does not see or recognize the SIM even after a reboot. The problem may be caused by the following:

The card is damaged or its expiration date has expired;
Violation of the integrity of the contacts in the connector;
The gadget is programmed for a specific operator, and does not recognize other SIMs (most likely it was purchased abroad);
Unsuccessful system flashing;
Contamination of SIM card contacts;
Broken card holder (re-soldering the contacts in the card slot will help).

Read about operators: How to unlock an MTS SIM card quickly and for free

Instructions

Let's look at step-by-step instructions for removing a SIM card from the depths of an iPhone. It is important to follow the correct sequence of actions, take your time, and be extremely careful and careful. The manual is universal and suitable for all iPhone models: 4, 4s, 5, 5c, 5s,6, 6 Plus, 6s, 6s Plus, SE, 7, 7 Plus, 8, 8 Plus, X, XS, XS Max, XR, 11, 11 Pro, 11 Pro Max, 12, 12 mini, 12 Pro, 12 Pro Max.

Turn off iPhone

How to open the tray

Despite the simplicity of the operation, some users manage to make mistakes when opening the tray. They break it, or remove the SIM card in such a way that the card “wedges” inside the case. The most common mistakes are made when using non-original devices to open the tray.

Key from the box

A special device in the form of a bent strong wire. Comes with any iPhone, located in the box with the device. Everything is quite simple here:

With one hand you fix the phone, with the other you carefully insert the tail of the key into the special hole on the tray.
Press the key slightly until the carriage snaps slightly away from the body.
Take out the key and remove the tray with your fingers.

Be careful. New smartphone models have a nano-SIM. It may accidentally fall out of your hands and get lost due to its miniature size. Perform all operations on a table or other surface.

With a needle

If you don’t have a special key at hand, you can try to remove the SIM card using a sewing needle. But there are a couple of nuances here:

Wear a glove or a thimble to prevent injury to your hand.
The sharp end may slip and damage the inside of the case and board. Place the needle strictly vertically, do not press with all your might. You need to find a special area that is responsible for opening the tray.

Paperclip

The same principle applies here as in other cases. An unbent strong one works better than a needle, since it has a blunt metal tail rather than a point. Unbend the paperclip and make it into something like an original key, open the tray as described above.

Correct installation in the slot

Carefully push it in

Now you need to turn the phone so that the SIM card tray faces up. Otherwise, the card will simply fall out when you push the carriage into the slot. Refer to the key hole to position the tray correctly. Carefully insert the carriage without bending it to the sides. Push the tray in with your finger until it stops and you hear a tactile click.

Turn it on and check

Start your iPhone and wait for the system to boot. If everything is done correctly, iOS will start, and after a while, the network icon will appear in the top status bar. A little later, the smartphone will receive network settings from the mobile operator. In rare cases, it is necessary to configure Internet settings manually.

Let's consider a number of issues related to breakdowns and SIM card jams. We will also cover the topic of eSIM and ways to trim a standard card for a nano-SIM.

What to do if your SIM card is stuck

A SIM card can jam and become tightly stuck in the case for various reasons:

old card with broken plastic, chips or cracks;
The SIM card was cut to the required size at home;
the tray is not closed correctly or is bent.

In all cases, you will have to act extremely carefully. If the tray opens even a little, you can try to set the card in place using a thin needle. When the tray is firmly in place and the SIM card does not move, you need to contact the service center, the technicians will disassemble the case and change the SIM card.

How to crop for nano-SIM

iPhone SE (2nd generation)
iPhone 11, iPhone 11 Pro, iPhone 11 Pro Max
iPhone XS, iPhone XS Max
iPhone XR
iPhone X
iPhone 8, iPhone 8 Plus
iPhone 7, iPhone 7 Plus
iPhone 6s, iPhone 6s Plus
iPhone 6, iPhone 6 Plus
iPhone SE (1st generation)
iPhone 5s, iPhone 5c, iPhone 5

There is no fundamental difference between a regular SIM and a nano-SIM, except for the physical size. The user can insert a small card into a special plastic adapter. This way you can use, for example, a nano-SIM in an iPhone 4S.

If you have a larger format card on hand, you can cut it out to fit the nano standard. To do this, it is better to use a sharp blade or a stationery knife:

Outline the contours of the future SIM card with a thin pencil directly on the plastic. Be sure to use a ruler. The exact dimensions are written above. Observe the layout of the key (cut corner).
Secure the card on the table or floor. Press the ruler on one edge, along the contour of the future card. Run the tip of the blade or knife several times. Ideally, you need to cut, not break off, the plastic. Run the blade along all sides of the future SIM card.
When the excess plastic is removed, carefully sand the edges with sandpaper (zero sandpaper).
Insert the cut SIM card into your smartphone and check the network functionality.

In principle, you can initially arm yourself with sandpaper and grind down the edges of a large SIM card to the desired size. This way you probably won't go wrong, but it's a very long process.

What to do if the SIM card does not work

Not every SIM card will work on the purchased iPhone. If the card is not detected or suddenly ceases to be recognized by the device (writes an error), there are several options for the development of events:

Malfunctions in the SIM card itself. Physical failure, the chip board is faulty. Only replacing the card will help.
There is no support from your operator in this region. Try using a different communication provider.
iPhone is locked to a specific mobile operator. For example, if the user bought a smartphone in the USA or Canada. Very often, devices from North America are flashed for the local telecom operator. Such smartphones cannot be used in other countries. Only jailbreak will help if it is possible on this device.

If the SIM card is detected normally on other smartphones, there is operator support; the contact pads in the smartphone itself may be damaged. We recommend taking the equipment to a service center.

How to Add a Second SIM Card to Any iPhone

Adapter for 2 SIM cards

The first method is quite simple - using a special adapter for two SIM cards. This is a thin cable lining that is installed inside the hole for the SIM card. Installation algorithm:

The cable is wrapped inside the main connector, and an alternative SIM card is placed on the second end of the adapter.
The main card is placed in its original tray. Close carefully so as not to damage the cable.
The adapter is covered with a thick cover on top.

The device is somewhat reminiscent of the well-known TurboSIM (R-SIM), which was used on locked devices. In some modifications, it is a ready-made tray with a cable that replaces the standard carriage for a SIM card. To make calls from the second SIM card, you need to switch the card through: “Settings” -> “Phone”. The average cost of such an adapter is from ₽270 to ₽750 and does not fit every iPhone model.

Case with SIM card slot

A very useful accessory if you buy a case from a trusted brand. As a rule, such a bumper solves two problems at once. The first is an additional power bank, which is sewn directly into the case. Capacity varies from 1500 mAh to 5000 mAh. The second task is the SIM card tray itself. It is usually located on the inside of the case.

Find a place to install the SIM card on the case. Insert the card, if necessary, use the enlarger adapter. Usually it comes with a bumper.
Carefully place the case on your smartphone. Insert the gadget at the sharpest possible angle so that the special lighting plug can easily fit into the native iPhone connector.
Download the app to switch between SIMs. The most popular: iSIM Mate, AIFORD.
Install the utility on your smartphone. Grant all permissions that the software requires for it to work correctly.

The program runs via Bluetooth, so this module must be turned on. Go to the application settings, set an alternative call for the second SIM card. Don't forget to turn on the program every time you restart your iPhone. It must work in the background, otherwise the SIM card will be inactive. The cost of such a device is quite high. For a good case from Laiford or IKOS you will have to pay about ₽4000-₽5000.

Bluetooth keychain with SIM card inside

Essentially, this is the same option as the cover. Only here the second SIM card is placed inside a special keychain. Some models can boast not one, but two additional slots for SIM cards. The result is three SIM cards for a smartphone. Connection via a special application.

Calls and the Internet on the second SIM card are also controlled via Bluetooth. It is important to note that the user will not be able to use the wireless headset if he has a second SIM card in a case or key fob. Therefore, these devices are most often used to access the Internet. You need to charge the gadget every 2-3 days. The cost of the device is within ₽3000.

Where is the connector?

The location of the SIM card tray has changed twice. The space for the connector can be located in two places on the device body, depending on the model:

At the bottom, on iPhone 3GS and older versions.
On the right side, on devices newer than the iPhone 3GS.

If you have a smartphone in your hands where the slot is located on the left or upper part of the body, most likely it is a Chinese counterfeit running on Android.

What is the difference between two SIM cards and the presence of an eSIM module on an iPhone

It is better to consider this issue in the context of the Russian Federation and most of the CIS countries:

Two physical SIM modules mean that the user can install a pair of cards from different (or one) telecom operators that operate in the home region. In this case, both providers will work simultaneously.
The presence of an eSIM chip means that the device can work with a virtual SIM card, if at least one telecom operator supports it. By the beginning of 2022, there are practically no operators in the Russian Federation and CIS countries that can provide full eSIM support. The experimental launch of the technology is being carried out by MTS and TELE2. In the meantime, you can be content with a single tray for a regular card.

The eSIM chipset itself is much more convenient than its physical counterpart. You can attach several tariff plans from different operators to it. But these are prospects for the near future; the technology is difficult to license in the CIS and Russia in particular.

How to install dual nano SIM cards

To install two nano-SIMs into your phone at once, you will need to use a case or an adapter. The only solution out of the box is available on Chinese versions of smartphones starting from the 11th series. There is a double tray for a SIM card. But these devices only work in mainland China.

How to connect eSIM

At the moment, there are several ways to connect a virtual SIM card. In this case, the user no longer needs to buy a tariff plan in the store. Everything can be done remotely via the Internet. Let's look at each connection method separately.

QR code

This method is used by MTC, as well as some foreign companies. To activate eSIM via a QR code, you will need access to the State Services account or to your personal profile on the mobile operator’s website (if the user is already a client of the company).

The SIM card settings will appear in the corresponding section on iOS.

Operator application

Some telecom operators are already integrating eSIM connectivity into their apps. To connect in this way, you need:

Enter eSIM manually

Another way to connect a virtual SIM card is to enter data manually. The information must be provided by the mobile operator.

Go to the “Settings” of your device.
Tap on “Cellular” (or “Mobile Data”).
Select “Add cellular plan”, scroll to the bottom of the display.
Click on “Enter data manually”, enter the information provided by the operator.
Save your changes.

The operating system only manages one data plan per eSIM. However, you can put several numbers into a virtual SIM card at once. To switch between tariffs, go to “Settings”, then to “Cellular”. Set “include this number” next to the selected tariff.

What to do if the tray is lost

Without the aluminum tray, the smartphone will not work. You shouldn’t do anything on your own and put pieces of paper or cardboard to secure the SIM card. It’s easier to buy a tray in a radio parts store, on Avito, or contact the nearest service center. They will ask about ₽300-₽500 for a tray. If you have free time, you can order the accessory in China. There you can find a tray for ₽50.

Trimming

The cost of replacing a standard SIM card with a nano, in the same MTS, for example, costs a lot - 24,300 rubles.

Therefore, many people prefer to cut it to the desired format themselves. This will take literally a few minutes, and does not require any special skills or equipment - the entire procedure is performed with ordinary kitchen scissors.

This is what “modifications” look like, which you can do on your own - just trim the edges. For “sixes” the one on the far right is suitable.

Many service companies offer to quickly and efficiently “adjust the nano-size” to the sixth iPhone for little money.

If you decide to cut it yourself, do not forget to first mark the characteristic beveled corner - you can put a dot on the reverse plastic side with a marker. We also recommend making something like a pattern - for the nano-sim parameters indicated above. This will make cutting it out much easier and less likely to make a mistake.

But here is an original solution from K. Ropp, which helps to quickly cope with the task.

Guide how to insert SIM

-cards in the Apple iPhone smartphone6

. Especially for the article:

Guide how to insert SIM

-card in the Apple iPhone 6s

Simply select the desired size and make markings along the intersection lines. The fit is almost perfect this way. And the likelihood of damaging important elements of the chip is minimized.

It’s better to cut with a small allowance, and then sand off any excess with sandpaper. Even if you go a little onto the metal surface, it’s okay. Usually the chip is placed in the center and will not be damaged.

After trimming and grinding the ends, remove a little thickness from the reverse plastic socket, since the factory SIM card, and therefore the slot for it in the iPhone, is 0.09 mm thinner - that’s what needs to be removed. If you do not do this, you will then not be able to open the port and remove the stuck card. We recommend inserting it into the tray from time to time and adjusting it so that it does not protrude above its metal side, and it can then be pulled out. After that, thoroughly wipe it from dust and that’s it - the nano-sim can be used.

How to insert or remove a SIM card from Apple devices: step-by-step instructions and tips for owners

What should you do if you have an iPhone and strong strangers ask you for your phone so they can insert their SIM card and make a call? But you can’t refuse them, because calling your mom is sacred? Or are you changing mobile operator? Or are you simply selling your Apple device and need to get your SIM card? It would seem like an elementary operation, but difficulties can arise with it.

How to insert or remove a SIM card on various iPhone, iPad models

It’s worth mentioning right away that SIM cards are inserted into the iPhone using a special small container. It is securely fixed in the case along with the operator communication chip.

This “box” for a SIM card is usually located on the side panel of the device, and can be located at the top or bottom.

Only a few Apple devices (iPhone 3GS, iPhone 3G) had a SIM card slot built into the top of the phone.

The appearance of the container is practically unchanged. It is a compartment with a hole for a special key.

On the right side we find a SIM card slot with a hole for the key

So, the key must be inserted into the hole and press lightly

You need to apply force carefully, since the Apple device is stuffed with boards and chips from top to bottom. And they are very easily damaged by any scratch

The key used to remove the SIM card slot

Most likely, the container will give in almost immediately and “jump out” as soon as you use a special spring.

Using the key, pull out the container with the SIM card

The question immediately arises: where can I get the key? Often, phone manufacturers, and Apple is no exception, put SIM card slot openers in the box with the device and secure it so as not to scratch the device during transportation.

We find the key in the box with the device

But if you didn’t find such a gift in the box, don’t despair. To open a slot, you can use any item that has similar physical and geometric characteristics. The most popular choice for opening the SIM slot is a regular paper clip.

Paper clips used to open and remove the SIM card tray

A special key, like a paper clip, can be replaced with anything. For example, a needle (use only the blunt end), a toothpick, a piece of stiff wire, etc.

And the operation can be successfully carried out without a special key.

Straighten the paper clip.
Insert into the hole of the container.
Gently press until the slot pops out.
We take out/insert the SIM card. Use a paper clip to remove the SIM card container

Do not use brute force, press too hard or try to pry out the container with a knife. Most likely, this will lead to disastrous consequences and ruin the integrity of the case.

How to remove a SIM card from an iPhone if it's stuck inside

Unfortunately, cases of SIM cards getting stuck in iPhones are not uncommon. This is especially true for so-called cut and self-cut SIM cards in 3FF and 4FF formats.

SIM cards of 2FFm 3FF and 4FF formats, which are used when operating smartphones

If the SIM card is stuck, you must try to put it back in the tray, and then repeat the operation of pulling out the slot:

shake your phone: perhaps the SIM card will snap into place immediately;
try the procedure of opening and closing the SIM container a couple of times;
Find a small piece of thick plastic film or very thin plastic. Using scissors, cut it to a strip, slightly narrower than the SIM card slot. Try, by pushing this “tool” into the slot between the container and the phone, to put the SIM card back into place in the tray. When you feel that the card is in place, carefully try to open the container again.

If the SIM card container does not move at all

If the SIM card slot does not respond at all to your attempts to open it, you will not be able to avoid contacting a service center.

Such a problem can only be solved by completely opening the device, and without specialized skills and tools, the likelihood of damage to the device is extremely high.

Removing the SIM card from your Apple device is easy. If you have problems with this, do not panic and immediately rush to the service center. All you need is patience and a little skill, and you can cope with even the most difficult task.

Alexey Gerus
Print

If the tray does not eject at all

There is no need to fanatically press the button with a paper clip if, with light or moderate pressure, the tray does not come out of the iPhone or iPad. Most likely, in your case you will have to contact a service center for help, unless, of course, you have the useful skill of disassembling and assembling such equipment. And it would definitely be a bad idea to try to pull out the tray mechanically: picking with a knife or other sharp objects will not only ruin the appearance of the equipment, but can also lead to more serious damage if a piece of the tool breaks off and remains inside. You don't want your beloved 5s or 4s to suffer even more damage, do you?

Often, a complete blocking of a slot occurs when the SIM card in use was cut from an old one that did not fit the parameters. Believe me, re-issuing the card will be much faster and will require much less money than a similar breakdown of an iPhone or iPad. Don’t be lazy to replace the card so that you don’t have to contact the service center for help later due to your own carelessness.

Some problems with an iPhone or iPad, such as removing a SIM card without using a key, can be solved on your own, but the main thing is to remember that service centers exist for a reason and are also ready to help in a difficult case. Go for it, but adequately assess the situation and don’t panic!

An iPhone is expensive, which instinctively forces the owner to treat it with care so as not to accidentally damage anything.

Many people put a SIM card right in the store when purchasing, they don’t pay attention to it, and when they need to get a SIM card, difficulties arise.

We are used to the fact that when we remove the back cover we immediately see it and can easily pull it out, but this is not the case with the iPhone.

The SIM card is located in a special tray, which is impossible to open simply by hand without a key, paper clip, needle or other similar devices.

Is it good or bad? The good thing is that if you need to take out the SIM card, you don’t have to disassemble the phone.

It’s bad - if you have to pull it outside the house, you may not have the tool. Finding it usually isn’t a problem, but you still have to spend time.

NOTE: in iPhone 5s, iPhone 4, iPhone 5, iPhone 6, iPhone 4 s, iPhone 7, iPhone 6s plus, iPhone SE, iPhone 8, the slot is located on the side or only in 3 models in the end part at the top.

iPhone

To locate the SIM card tray, find your model name at the bottom. To open the SIM card tray, insert a paperclip or SIM eject tool into the hole next to the tray. Push the tool inside the iPhone without using too much force. If you have trouble removing the SIM card tray, take your device with you to a carrier center or an Apple Store for help.

After removing the SIM card from the tray, notice the notch in one of the corners of the new SIM card. Insert the new SIM card into the tray - due to the notch, this can only be done one way

Then push the tray all the way into the product in the same orientation that you removed it. The tray can also only be inserted on one side.

The following devices have the SIM card tray on the right side panel.

iPhone 11 Pro
iPhone 11 Pro Max
iPhone 11
iPhone XS
iPhone XS Max
iPhone XR
iPhone X

The SIM tray on iPhone 11, iPhone XR, iPhone XS Max, iPhone 11 Pro, and iPhone 11 Pro Max in mainland China can accommodate two nano-SIM cards at the same time.

The following devices have the SIM card tray on the right side panel.

Standard method

The iPhone usually comes with a needle, also called a key. If it is not there, you can use other means in the same way, which we will return to later.

To complete the task with the key, do this:

Using a paper clip, press the mechanical button located on one side of the connector cover.
You will hear a click and the cover will come off.
Using your fingers, remove the connector.

Depending on the iPhone model, this connector may be located on the side or top. But on iPhone 4, 5, 6 it is always on the side.

Installing Nano-SIM on your phone

After cutting the SIM card and giving it the desired size, you can install it in your smartphone. This is done as follows:

Turn off your Samsung Galaxy S8 and disconnect the device from the power adapter if it is charging at this time.
Find a key clip in the cell phone box.
Take the gadget in your hands with the front side facing you. Insert a paperclip into the round hole located in the connector cover and apply light pressure.
Once the slot moves out a little, remove it completely from the phone.
Place the SIM card correctly in the tray. Here, too, the cut corner serves as a guide.
If necessary, insert a MicroSD memory card into the appropriate slot.
Return the SIM holder to its place. A soft click will indicate that the slot has been successfully locked.

When the SIM card is installed, the smartphone can be turned on. If everything is done correctly, after loading Android, the system will recognize the connected SIM card and show the signal level. If this does not happen, try removing and reinserting the card again.

Today, the Nano-SIM format is widely used only in mobile products from Apple and Samsung. Other phones usually use MicroSIM cards. If you ever need to install a nano card into a micro slot, you can use a special adapter. Such adapters are inexpensive and are sold in almost all cellular stores.

In this article we will tell you how to correctly insert a SIM card into your phone yourself. New modern models are coming out with convenient slots into which cards of the required size can be inserted without problems.

And all popular mobile operators produce unique constructors - SIM cards in three popular sizes: nano, micro and standard.

Risk group

The exact cause of the development of this disease is unknown. However, there are some factors that increase the likelihood of a tumor:

diseases of viral, infectious origin (in the mother),
genetic predisposition, mutation,
abuse of bad habits,
insufficient oxygen supply to the fetus,
inflammation, inflammation
drug treatment,
poisoning by toxins,
irradiation,
childbirth with complications,
prolonged exposure to sunlight, in a solarium,
elderly age,
early meningitis,
stroke with cerebral hemorrhage,
encephalitis,
work in hazardous industries,
chemotherapy,
heredity.

https://youtube.com/watch?v=wXlOR0xt5J4

Risk group

Rathke's pouch cysts rarely appear in humans. The congenital disorder occurs in 1% of the total number of benign neoplasms. Doctors were able to identify the category of the population susceptible to developing such a disease.

These include:

Patients of mature age, in whom the tendency to form a cyst appears after 40 years.
People treated for meningitis.
Patients after strokes with cerebral hemorrhages.
Those who have had encephalitis.
Workers in hazardous conditions.
People after chemotherapy or radiation.
Patients whose relatives have such a disease or other brain tumors.

What can't you do?

So, now let’s talk about what you absolutely cannot do if you don’t know how to get a SIM card out of an iPhone 4. First, you need to carefully handle the object with which you will try to replace the key. Since the end may be sharp, do not press too hard to avoid causing damage. Also, do not apply excessive force so as not to break the key itself (or what replaces it). If something remains in the hole, it will be difficult to clean it later and remove the card from the phone.

In addition, you need to be careful with the slider itself when placing the card there. So, first you need to place the SIM card itself in the correct position. After that, making sure that everything is in order, you can close it, placing the card inside the case. For the phone to see the map, you need to reboot.

Last time, we looked in detail at how to clear memory on an iPhone using and without iTunes, and wrote a short instruction that you can read. Currently, it is difficult to imagine a phone working without a SIM card. All iPhones and most iPads are designed for communication between users, friends, colleagues and people close to us. Communication is possible both via the Internet and through the network of a mobile operator using a SIM card. How to insert a SIM card into iPhone 7? Read on.

A SIM card is an intermediary that provides the telecom operator with information about your device, its access to voice communications and data transfer. Full operation of the device is impossible without a SIM card. So, in this article we will deal with the seemingly simple question of how to insert a SIM card into the iPhone 6 and most other iPhone models. First, let's look at what type of SIM is required for normal operation of the device.

According to official information from the Apple website, the iPhone uses the following types of SIM cards, which are shown in the image. Therefore, be careful and check with the telecom service operator’s consultant or insert the SIM directly at the communication salon, in the presence of an experienced assistant.

How to remove a SIM card from an iPhone 5s

All we need is to find out where the SIM card tray is located on the smartphone itself and a tool to remove the SIM card from the gadget.

The main difficulties that may arise on your way to removing a SIM card are the availability of a tool, but this is not a problem. Let's make do with improvised means.

To begin with, if you still have a paperclip that came with the device, we recommend using it. Remove the case from your smartphone and find the SIM card tray. As a rule, its distinguishing feature is the presence of a hole in the housing on the side of the device. Insert an original Apple paper clip into the hole and press with enough force to allow the tray with the SIM card to slide out of the grooves.

After removing the tray with the SIM card from the device, the message SIM card is not active will appear on the smartphone. We advise you to turn off your smartphone before inserting or removing a SIM card.

How to get a SIM card out of an iPhone 5 if you don’t have the original paperclip?

Probably everyone has toothpicks at home. Many people use toothpicks after meals, but not everyone thought that they could be used as one of the improvised means for removing a SIM card from an iPhone.

As a rule, a standard toothpick will not fit into the hole in the iPhone SIM card tray. To remove the SIM from the iPhone using a toothpick, you should sharpen its edges a little (make it narrower). Try to trim just a little on both edges. If you make it too thin, the toothpick will break when you remove the SIM card, be careful.

How to remove a SIM card from an iPhone 4

The safest way to remove a SIM card from an iPhone 4 without using the original key is to use a paper clip. Surely many people have a very ordinary paper clip lying around. Bend it or straighten the long end as shown in the image and insert it into the SIM card tray of the iPhone 4.

Correct Method

It is not difficult to remove a SIM card from an iPhone - just follow the simplest instructions. The method we have presented is relevant for any iPhone smartphone model; you can easily find a slot on the side (or top) side of the case.

Before you take the SIM card out of your iPhone 6, you need to find the SIM card slot - it's easy, just find the small round hole. Now you can begin our instructions!

Arm yourself with a special paperclip, which is included in the device kit;
Insert the sharp end into the slot hole;
Press lightly so that the edge of the tray comes out;
Gently pull the backing with your fingers and remove the slot completely, now remove the SIM card.

It's simple! We figured out how to remove a SIM card from an iPhone 5S (or other model) in a few seconds. Let's give some useful tips that will be useful to you:

It is not necessary to turn off the device before removing it - all functions of the iPhone smartphone will be available, only the cellular network will be turned off;
Be sure to return the backing to the hole the same way it was removed.

Interested in the reverse process? Read our article about how to insert another SIM card into an iPhone without any problems!

Let's watch an interesting and useful video with other tips:

You already know how to remove a SIM card on an iPhone. What should you do if the standard components are lost and you couldn’t find the original paper clip? There is an exit!

How to insert a SIM card into iPhone 3g and 3gs

It’s phenomenal, but almost everyone, faced with an identical problem, immediately runs to the nearest service center, where specialists help them for extremely decent money.

Not many people think that you can do all this yourself at home, without even damaging your expensive iPhone.

Step-by-step summary.

First, turn off your iPhone. No matter how complex synchronized technology is, Apple’s phone likes everything to be done only according to the instructions. To turn off the device, press the power button located above the screen on the edge of the case for 5 seconds. Swipe your finger across the “Slide to power off” message that appears on the monitor to turn off your iPhone.

Next you need to find an external slot for the SIM card.

Unlike its predecessors, the iPhone 4S has it located on the right side. Here you will one hundred percent feel the seriousness of the question of how to remove a SIM card from an iPhone 4S. It is impossible to do this with naked hands.

Now Apple, traditionally, includes a special key in the iPhone set, which is inserted into a small hole on the slot and forces it to move out, allowing access to the SIM card.

What to do if there is no special Apple branded key in your iPhone box.

If you find that you do not have this key, you will have to call on resourcefulness to help.

Please note that the thought of using a needle to open the SIM card tray must be quickly banished. Otherwise, you risk damaging the tray locking system. Traditionally, experienced iPhone owners use an ordinary paper clip for these purposes, straightening it out first. But some inventive individuals manage to adapt a dental probe or a thin awl for these needs.

What to do if the SIM card is stuck.

Phew, the connector seems to have been opened, but the SIM card itself, as before, does not want to come out. This means that you will not only have to solve the question of how to remove the SIM card from the iPhone 4S, but also deal with the problem of removing a stuck SIM card.

Yes, yes, and some fans of Apple phones may realize this. Fortunately, this phenomenon is not widespread.

It is completely appropriate to want to contact a service center with a problem, where they will solve it, charging a tidy sum for it. Do not hurry! Try to do everything yourself.

If the SIM card is stuck, the connector extends only a couple of mm. To remove the SIM card, craftsmen advise using something thin but strong. A model knife or film from a folder for papers fits perfectly.

You just need to insert them between the phone body and the slot on the screen side. Next, all that remains is to pull out the record along with the slot, pressing it against the screen.

If you don't succeed the first time, don't despair. This procedure requires skill.

Be the first to comment on this article!

Theses

How to remove a SIM card from an iPhone.

How to remove a SIM card from an iPhone. Instructions for using iPhone. How to remove a SIM card from an iPhone? How to remove a SIM card from an iPhone. Like almost everyone else and take the SIM card included in it. How to remove a SIM card from an iPhone 4. How to remove a SIM card from an iPhone 4 macmyapples. Created by: macmyapples. How to remove a SIM card from an iPhone - Apple-iPhone. How to remove a SIM card from an iPhone. The iPhone 4 and all subsequent iPhone models have a SIM card tray. How to remove a SIM card from an iPhone. How to remove a SIM card from an iPhone. How to remove SIM card from iPhone 4S?

How to remove SIM card from iPhone 4S? To remove the SIM card, remove the SIM card from the iPhone. How to remove a SIM card from an iPhone and iPad: we disassemble simple and... did not remove the SIM card from the iPhone, get the SIM card from How. How to remove a SIM card from an iPhone

— how to insert a SIM card into an iPhone. Creator: Geek. How to remove a SIM card from an iPhone. How to remove SIM card from iPhone 4? How to remove a SIM card from an iPhone 4?

In order to remove the SIM card from the iPhone, for. How to get it

Sim Card

From
iPhone
3 - voronin. Method 3 of 4: iPad 2, 3, 4, and Mini.

how to open the sim card slot on iphone

iPhone 6s disassembly. Not enough memory, how to increase memory? Copy of iPhone 6s.

iPhone 5 clone, how to disassemble and change SD memory card

How to insert a SIM card into iPhone 5S | How to Insert a SIM Card into iPhone 5S

How to remove a SIM card from an iPhone - how to insert a SIM card into an iPhone

How to open a port

If pressing the hidden button in the hole next to the door does not open the SIM slot, then there is no point in pressing harder on the key needle. This will not help open it, but will only increase the risk of damage to the appearance of the iPhone itself, internal parts and SIM card.

Try shaking the device lightly from side to side. It happens that the parts get caught on each other or a speck or sand gets into the mechanism.

Shake it lightly and try to open it. If there really was a foreign object in the way, then the movement caused it to move and no longer block the opening.

If this does not help, then you should not try to pick at the edge of the slot with a knife or other sharp object. There are known cases when the upper part of the SIM port is cut off or broken off. In this case, it is no longer possible to use the iPhone. After all, the removed cover no longer protects the gadget from dust, moisture and sand.

In this case, you need to contact an official service center. There they will not only remove the SIM card from your iPhone, but also order a new SIM slot carriage. Be prepared that replacing such a part can be expensive and time-consuming, because original parts will need to be ordered from production, and they are all located nearby.

How to remove a SIM card from an iPhone using a key

Removing a SIM card is a simple process, you just need to follow the rules and comply with safety standards. The SIM removal method proposed below is universal and can be used for mobile devices of all iPhone models.

You need to find a slot. It is located on the top or side of the device. It is easy to distinguish - it should have a round hole.
A special key is inserted with the sharp end into the connector. The key must be included in the kit.
Light pressure is required for the tray to slide out of the phone body.
After this, you need to pull the slot, removing it out. Now you can get a SIM card.
It is better to put the slot in place so that it is not lost.

The process is simple and only takes a few seconds. It should be noted that the backing must be inserted with the same side as it was pulled out. If the backing is inserted incorrectly, the phone will not recognize the SIM card. There will also be a possibility of the grooves breaking.

Inserting and removing a SIM card from an iPhone 5

Since the most questions arise with this model, we need to analyze the method of removing the SIM card with it

When purchasing a new Apple phone, you need to pay attention to the dimensions of the card and the size of the connector for it. The fact is that each model has its own indicators

The SIM card for different models can be reduced, standard or enlarged.

That is why, before purchasing a mobile device, you should consult with a service employee and find out from him what size SIM card will fit the gadget’s tray. Buying the wrong card will not only result in a waste of money, but also damage your communication device.

However, after the release of the above-mentioned phone, the situation changed, since SIM cards began to be sold in the required size. Therefore, many users often have a question about how to insert a SIM card into iPhone 5 and subsequent models themselves. So, to insert a SIM card into these models, you need to follow the following instructions.

First, you need to purchase a SIM of the required dimensions so as not to have to worry about trimming. You need to carefully open the tray where the card is inserted using a special key that comes with the purchased device. It is not recommended to use other objects to open the slot if there is a key, as there is a possibility of damaging the mobile device. Next, you need to lightly press the tray cover with a key so that it protrudes beyond the casing by a few millimeters

After this, you need to pull out the slot and insert a card of the desired size. The card chip should be on the bottom, and the side with the name of the cellular operator company should be on the top. You need to insert the slot into the proper place by pressing on it. He must go in all the way. You can pull out the slot by pressing the key into the connector located on the tray.

After the procedure has been completed, a message about blocking the card will appear on the phone display. You need to unlock your SIM card. To do this, enter a PIN code. If the network is not detected, you need to go to the “Settings” section and find the item called “Operator”. In addition, you can set up automatic network selection, which will make using the communication tool easier.

After completing these operations, you will be able to communicate by phone. If, after the above steps, the SIM card does not work, you should contact a mobile phone store or Apple service center. The owner of the phone should be helped there.

iPhone doesn't come with a key

There are times when the kit does not include a special key for opening the SIM card slot. If you just purchased your mobile device and don’t have a key, you need to contact the Apple office with a complaint. It must be satisfied and the user must be given a new device for opening the tray.

If the part is lost during long-term use of the phone, it is better to buy a new key or use similar items. The most commonly used are paper clips and needles, but it is better not to use the latter, as they can damage the equipment.

In addition, under no circumstances should you remove the SIM card with an easily broken tool. Its tip may break off in the connector, as a result of which you will have to take the gadget to the center for repairs. For this you need to pay more money than for purchasing a new key.

The card is stuck: what to do?

Important! Be careful - do not apply too much force so as not to break the capricious technique. If the SIM card tray gets stuck during the ejection process, we recommend doing the following:

Try to carefully pick up the backing with a sharp object and pull it towards you, moving it slightly in different directions;
Using a thin needle, try to correct the position of the SIM card, which is lying unevenly. Be careful not to try to push the needle deep inside, so as not to touch the mechanisms;
Lightly tap the device on the edge of the table so that the card is in the desired position, now you can pull it out.

If you are unable to resolve the problem yourself, contact the service center. Our specialists will cope with the task - in a couple of minutes you will receive a smartphone with an open slot!

Now you can easily remove the SIM card and can change it to another if necessary. We hope our tips will help you!

In order not to waste money and your own time on trips to the service center, you need to know in advance how to insert and remove a SIM card so that when replacing it you do not damage the connector of your mobile device. In addition, you need information about which slot to insert the SIM card into. It is worth saying that starting with the iPhone 5, the device includes a tray for special application. Therefore, you should not insert regular SIM cards into the tray.

How to remove a SIM card from an iPhone using a key

You need to find a slot. It is located on the top or side of the device. It is easy to distinguish - it should have a round hole.
A special key is inserted with the sharp end into the connector. The key must be included in the kit.
Light pressure is required for the tray to slide out of the phone body.
After this, you need to pull the slot, removing it out. Now you can get a SIM card.
It is better to put the slot in place so that it is not lost.

Inserting and removing a SIM card from an iPhone 5

Since the most questions arise with this model, we need to analyze the method of removing the SIM card with it

When purchasing a new Apple phone, you need to pay attention to the dimensions of the card and the size of the connector for it. The fact is that each model has its own indicators

The SIM card for different models can be reduced, standard or enlarged.

Removal safety

There are situations when you need to quickly remove the SIM card from your phone. At the same time, the removal rules are often forgotten, as a result of which the most important connector of the gadget is damaged. Therefore, you need to carefully carry out the process by following the following instructions.

The phone is taken out of the case. Since the latest models have the tray located on the side of the device, the case will make it difficult to access the SIM card.
You need to turn off your mobile device. To do this, press the “Power” key. The button is located at the top of the gadget. A slider with the words “Turn Off” will appear on the display. You need to swipe across this icon from left to right.

After this, the device will be turned off. It is not recommended to perform the SIM removal process while the phone is turned on.

The model kit should include a special key that opens the SIM card slot. You just need to insert it into the hole located on the SIM tray. After that you can pull it out.
In order not to lose the slot, you need to carry out the entire process, that is, insert it back into the device.