All the lights on the Indesit washing machine are flashing - what to do

All indicators on the Indesit washing machine are flashing: reasons and error codes.
What to do if the lights are blinking, but the machine does not turn on. Tips for troubleshooting Indesit machine problems yourself. Reading time: 23 min Category: Cleanliness

• The meaning of the code
• Other reasons for program crashes and blinking indicators
• Common breakdowns when the lock on a washing machine blinks
• Error codes indesit w 105 tx
• Why do all the lights on my washing machine blink?
• Causes and diagnosis
• Kandy washing machine errors without display
• How to determine the error code on cars without a display
• Error codes indesit w 105 tx

The meaning of the code

According to established tradition, we will begin with a general decoding of the error code, in this case code F12; such a decoding can be found in the operating instructions for the Indesit washing machine. And then we will provide a more detailed transcript, which will finally shed light on the problem. So, the general interpretation of error code F12 can be presented as follows: “the control module has stopped interacting with the buttons and lights of the control panel.”

Essentially, in this case, the Indesit washing machine states that there is no connection between its two most important modules. However, the connection was not completely lost, since the module was able to transmit information about the error to the user, which means that the electronic module retains some control over the control panel. Despite this, error F12 is accompanied by the inability to use the control panel in any way; in rare cases, even the on/off button does not work.

How and under what circumstances does it manifest itself?

If the Indesit washing machine does not have a display, then the electronic module (bypassing the usual circuit) will connect some control panel lights, which, in fact, will indicate an error. We are talking about the “Super Wash” and “Wash Delay” indicators that are on. On some models of Indesit washing machines, only the speed indicator may blink.

Error F12 in 99% of cases appears shortly after turning on the machine to the network. In this case, the user does not yet have time to select any washing program, or indeed do anything with the control panel. The Indesit washing machine freezes immediately, in addition, the on/off button may fail and then you will have to turn off the power to the machine by unplugging the power cord from the socket.

We find and eliminate the causes

The malfunction caused by error F12 can often be eliminated by restarting the Indesit washing machine. Moreover, the reboot should not be done anyhow, but according to the following scheme.

• We turn off the washing machine with the on/off button if it is working.
• Disconnect the power cord of the Indesit machine from the power supply.
• We wait for 2-3 minutes.
• We turn on the machine to the mains and press the on/off button.
• If the error persists, repeat the above steps two more times.

If the malfunction has not been resolved within 3 reboots of the machine, such actions should be stopped so as not to damage the control module even more. If rebooting does not help, it means that a serious breakdown of the control module has occurred, or the contacts connecting the module and the control panel bulbs have oxidized. With such a problem, there is little that can be done on your own. Unless you check connector J11, which, as you may have guessed, connects the display module to the control board.

If, after cleaning the contacts of connector J11 and the display module, the Indesit washing machine does not start working correctly, then the problem is in the control module. Perhaps the question will immediately come to your mind: is it worth doing repairs of electronic modules yourself? We will answer briefly - it’s not worth it! Most often, this ends in the final breakdown of the washing machine and the user being forced to contact a service center. Just keep in mind that the repair will cost 2-3 times more, since you will definitely have to change the spare parts of the “home assistant”, and this is completely different money.

So, a malfunction caused by error F12 can be eliminated only if the control board is not damaged, but only the contacts are burnt or oxidized. If the module breaks down, definitely contact a technician. Good luck!

What does it mean?

Blinking of all the indicators on the washing machine is a common problem with washing machines from Indesit. Owners of such washing machines most often turn to the technician, not knowing what to do. What causes this blinking?

The most common malfunction, when all the lights blink, is a malfunction of the electronic board, or rather a breakdown of its parts. As a rule, capacitors located on the board fail or contacts burn out when water gets on the board. It is quite possible to replace capacitors yourself, especially if you are good with a soldering iron. In some cases, the board has to be changed completely, which requires significant financial costs.

For your information! Replacing capacitors will save your budget by a large amount, the main thing is to correctly diagnose the breakdown.

This is interesting: How to lengthen the hose of a washing machine: extending the drain and inlet hoses

Other reasons for program crashes and blinking indicators

The LEDs on the control panel may blink not only due to a breakdown, but also due to incorrectly set parameters. There are a number of washing modes that provide the ability to connect additional functions:

• additional rinse
• higher degree of water heating,
• ironing

Instead of turning on, the indicator may flash if the selected program cycle does not provide a particular function.

The machine can generate a service error both at the initial stage of washing and during it. In cases where the weight of the load of laundry is not comparable to the number of revolutions or the maximum allowable volume of laundry provided for by the technical specifications, the spin process may not start. In this case, the buttons indicating a failure in the “Rinse” and “Spin” modes and the door lock indicator will start flashing. At this moment, it is necessary to restart the machine a second time, reducing the number of things.

After this, the execution of the specified program will stop. After a few seconds, the door will unlock, allowing you to make adjustments and start washing.

H2O

The code indicates a blockage in the drain system sector or the washing machine is not connected correctly. There are two options to solve the problem: cleaning the drain system or reconnecting the machine.

Thanks to the achievements of modern electronics, using the display provided by the Indesit washing machine, you can accurately determine the cause of a technical malfunction or inconsistency of input data. If the Indesit washing machine displays an error related to a malfunction of the control module, it is better to entrust the diagnostics and repairs to a specialist so as not to aggravate the situation.

Common breakdowns when the lock on a washing machine blinks

According to the experience of the RemBytTech workshop, there are a number of typical washing machine malfunctions that are accompanied by the lock blinking.

* Approximate PRICE OF TURNKEY REPAIR including the cost of spare parts and work of a specialist. The final cost of repairs will become known only after a specialist diagnoses the problem.

To summarize, it should be said that the flashing of the lock/key in itself does not indicate any specific problem with the washing machine. Therefore, you need to rely on additional symptoms that will help determine the range of possible malfunctions. For example,

It should be remembered that only a qualified specialist can determine exactly what happened to your washing machine after diagnostics. Therefore, if the machine has stopped functioning normally, and the lock on its body or display is lit or flashing, do not experiment or try to repair it yourself unless you are a master. This can lead to even more serious damage.

Contact the specialists of the RemBytTech workshop:

Within 24 hours after contacting, the technician will come to your home, conduct diagnostics and, if necessary, repair the washing machine. All work and spare parts are guaranteed for up to 2 years.

If your washing machine breaks down, don’t expect a miracle. Call “RemBytTech” right away!

Incorrect information from the water level sensor

This device has another name - pressure switch. It measures the pressure level in the tank when water enters it or when it is absent. When a certain liquid level is reached, the pressure switch is activated and closes the inlet solenoid valve. If there is a malfunction, the sensor may simultaneously send signals that the tank is full and at the same time empty.

The pressure sensor is usually located at the top of the housing, under the cover

The cause of the problem is the sticking of one of the contact groups that informs about an empty or full tank. The problem may also be hidden in the control unit and wiring contacts. If these components are working properly, you will have to replace the water level sensor.

Error codes indesit w 105 tx

The displayed fault codes for Indesit washing machines are presented in Table 1.

Table 1 - Errors, their names and possible causes

As can be seen from the table, for each error information there are several reasons for its occurrence. And as a result, the light warning shows the direction in which to start troubleshooting, which significantly saves the time of service workers and reduces the time the washing machine is under repair.

Why do all the lights on my washing machine blink?

It doesn’t matter: two indicators flash or all at once - this already indicates abnormal operation of the device. Most often, such a problem occurs with equipment.

If you have this particular model, take a look at the instructions. There is a decoding of the code that the system issues.

There are a number of standard situations when equipment produces indicator signals. Check:

• Is the water supply valve open? Unscrew it all the way. It is possible that water is not flowing due to a clogged mesh filter, intake hose or filter.
• Is the waste fluid draining normally? Remove the blockage in the drain hose and restore its correct location.
• Condition of the power cord. If damaged, replace it.
• Drum load. It should not exceed the norm specified in the instructions. Stop work and take out some of the laundry.
• Connection to sewerage. If the drain hose is located near the floor, the water drains out of the tank by itself. Raise it to a level of 40 cm from the floor.

If the red light of the lock is constantly blinking, the reasons may be the following:

• There is no water in the system, low pressure in the line.
• The loading hatch is poorly closed, the door lock did not work. Press the door tightly until it clicks.
• A power outage caused the electronic module to fail. Disconnect the equipment from the network for 10-15 minutes. After turning on, press the start button and the machine should resume operation.
• Child Lock is enabled. Press the button again to release the lock.

Have you ruled out all situations, but the indication has not disappeared? This may indicate breakdown of components and parts. For example, if the lock and rinse indicator blinks in an Indesit automatic washing machine, the motor may have broken down. We will consider breakdowns requiring repair below.

All indicators are flashing, the SMA does not turn on. What to do?

The main cause of failure is the control board. Its contacts, capacitors, and resistors could burn out. In this case, the machine does not work, all the buttons light up. You can inspect the board yourself:

• De-energize the SMA;
• Unscrew the top cover bolts from the back;
• Slide it back and remove it;
• Remove the detergent tray;
• Remove the control panel bolts. The module is mounted on it, and inside there is a board;

The module cover is removed after unfastening the latches or unscrewing the screws;

Inspect the board. Noticed burns or oxidation? Take the part for repair. The element is expensive, and its repair requires special skills.

What other malfunctions are there?

Hatch lock

The red lock indicator light is on.

The hatch does not lock or does not open after the end of the cycle. Check the hatch locking device (UBL). For this:

• Remove the cuff clamp;
• Unscrew the two UBL mounting bolts;
• Bend the cuff, put your hand behind the body;
• Get the lock out. If burn marks are visible, replace the device. Disconnect the wiring and install a new element.

Door lock

The lock indicator lights up, the door does not fit tightly, the latch does not fit into the hole. Inspect the hinges; they may be warped. Tighten the fastening screws. If the lock tongue is broken, you need to disassemble the door and change the mechanism. How to do this, watch the video:

A heating element

Did the “service” and “lock” indicators light up? It looks like the heating element is broken. In this case, the SMA may freeze in the middle of the program or wash with cold water. If you see a flashing “service” button, check the heating element.

It can be located in the front or back of the case. Details of the replacement are described in the article “How to connect a heating element in a washing machine.”

Level sensor

The lock is blinking on the screen. Water does not fill into the system, it is constantly drained, and the SMA slows down in the middle of the cycle. Check the pressure switch hose for blockages.

Remove the top cover. At the side wall you will find a pressure switch;

• Disconnect its wiring and disconnect the hose;
• Connect the tube in place of the hose;
• Blow into it;
• Do you hear clicks? This means the device is working. If not, replace it.

Motor brushes

Above we described how the indicators behave in the event of an engine malfunction. You may also hear extraneous sounds and notice sparking.

The motor brushes transmit electricity to the rotor to spin and operate the motor. Over time they wear off. Replacement is easy, the main thing is to select suitable elements for installation.

• Remove the rear cover of the SMA by unscrewing the bolts around the perimeter;
• Below you will see the engine. Disconnect its wiring, unscrew the bolts;

Remove the brushes from the housing. They are connected to the motor with a wire that needs to be disconnected;

Install new elements in reverse order.

Have you noticed any blinking lights on the control panel? Now you know what to do to fix the problem. If self-repair is not possible, contact a service center.

How to start repairs

When error F01 appears, first of all you need to check whether the electrical outlets are working. Once you are sure that everything is in order with the network, you can proceed to further steps.

It should be noted that a failure and the occurrence of error F01 does not necessarily indicate a malfunction. In some cases, there may be a coincidence. In order to check this, you need to turn off the washing machine, unplug the cord from the outlet, wait about twenty minutes and turn on the Indesit machine again. There is a chance that everything will work fine.

Let's assume that the breakdown that caused error F01 could not be corrected by simple means.

We'll tell you how to fix error F01 in this case:

1. You need to carefully inspect the socket and cord of the Indesit washing machine.
2. Next, proceed to a direct inspection of the washing equipment engine.
3. First, open the service hatch. The electric motor of the Indesit washing equipment is disconnected using an 8 mm wrench.
4. Next, to correct error F01, you need to remove the engine and inspect its brushes. To do this, unscrew it using a screwdriver. Then you need to inspect for possible damage or wear. If problems are found, it is recommended to replace these parts.
5. After replacement, everything is installed back.

The Indesit machine is then turned on to check how it works. Sometimes a clearly audible cracking sound is heard, which means there is no cause for concern. This noise is due to the grinding of the brushes.

If the problem that caused error F01 to appear is not related to the operation of the brushes, the inspection of the Indesit machine engine must be continued:

Now you need to pay attention to the control module. When examining the board, you need to determine whether there are traces of corrosion.

If they are found, they will need to be carefully cleaned. Now the motor winding is inspected. If it burns out, then the motor cannot be repaired - it will have to be replaced. This is a fairly expensive operation. If it is not financially feasible to do this, it is more profitable to buy a new, more modern car model. One of the possible causes of error F01 is a malfunction of the control module. If all other reasons are excluded, you will need to pay attention to this node. You cannot repair it yourself. This should be done by specialists who use the appropriate equipment.

One of the possible failures is when the drum suddenly stops during operation. In this case, the washer indicates error code F01.

In this case, it is recommended to take the following actions:

1. When error F01 appears, the first thing you need to do is turn off the Indesit machine.
2. Now you need to carefully drain the water from the tank of the Indesit washing machine.
3. After there is no water left, you must try to rotate it by hand.
4. If it moves normally, the reason for the F01 error may be too much laundry to wash. Now you need to divide the amount in half and try to wash half the original amount.
5. If these attempts are unsuccessful, you need to inspect the engine of the Indesit machine.
6. Perhaps error F01 appeared because the motor pulley was torn. Over time it can become worn and weakened. In addition, it may not have been damaged, but simply slipped. In the latter case, it is enough to simply install it carefully in place.
7. In the event of a malfunction of the electronic control board, the motor of the Indesit device may simply not receive a start signal. In some cases, you can do the fix yourself. To do this, it makes sense to try resetting the programs. If this does not help, then you will have to contact a workshop with such a malfunction.
8. If the brushes are worn or damaged, they will need to be replaced.
9. Voltage surges can lead to damage to the Indesit machine's electric motor and the appearance of error F01. What to do in this case? You will not be able to carry out repairs yourself. Only a specialist can fix this problem.

Causes and diagnosis

Even if the “F01” error occurred for the first time, it is necessary to carry out diagnostics and understand the cause of its occurrence.

The following circumstances may lead to malfunction:

• voltage drops in the network;
• breakage of the socket, plug or cord;
• physical wear of motor brushes;
• corrosion of electrical circuit contacts;
• malfunctions of the washing machine components;
• control board failure;
• turning the washing machine on and off during operation.

One of the possible causes of the failure is resetting the programmed settings. In this case, it is better to force a reboot of the machine:

1. Disconnect the device from the electrical network.
2. Leave for 30 minutes.
3. Insert the plug into the socket.
4. Start the machine.

If the reboot does not help, you will have to start troubleshooting, sequentially analyzing the operation of the nodes

There is a problem with the outlet, plug, or cord

Very often, the cause of the F01 code is an unstable voltage supply due to damage to the socket, cord or plug.

They need to be inspected, integrity checked and made sure there are no scorched areas indicating broken contact. In addition to a visual inspection, it is necessary to take measurements using a multimeter.

Mains voltage

Before you begin diagnosing a problem in the washing machine itself, you should check the voltage in the network. According to the rules, it should be 220V. It is this indicator that household appliances, including the Indesit washing machine, are designed for.

If the voltage in the network fluctuates, then the operation of the washing machine should be organized through a voltage stabilizer. This will extend the life of the equipment and reduce the likelihood of failure due to a short circuit.

Broken or stretched drive belt

The belt in the washing machine ensures that the drum rotates, which is provided by the motor.

If the belt has slipped, torn or stretched, it either does not perform its functions or performs it intermittently.

To verify the condition of the unit, you need to remove the back panel of the washing machine and gain access to the belt.

The worn part must be replaced with an identical one (all the necessary information is located directly on the belt itself) or, if it has simply fallen off, its correct position must be restored, paying attention to the grooves and pulley

Engine problems

Access to the engine can be gained through the service hatch - it is located on the rear wall. You can check the engine's performance after removing the element.

To do this, perform the following steps:

• remove the back wall;
• remove the drive belt by loosening the pulley;
• carefully disconnect the wires leading to the engine;
• remove the engine.

When disconnecting wires from the engine, it is very important not to forget which ones are attached where. To avoid confusion, it is recommended to draw up a contact diagram before removing the part. Diagnostic algorithm:

Diagnostic algorithm:

1. Inspection of carbon brushes. Over long periods of use, these parts tend to wear out. When worn out, they should be replaced with new ones.
2. Inspection of contacts. The problem can be caused by both dust and the smallest fractions of coal.
3. Checking the motor winding. In addition to visual inspection, it is necessary to use a multimeter to determine the resistance; this indicator should be in the range from 20 to 200 Ohms.
4. Inspection of the condition of the collector lamellas.

Corrosion of washing machine parts is not a rare situation. This is explained by the specific location and operation of the device itself - with the presence of moisture.

Metal elements, including the engine, are susceptible to corrosion. If the defects cannot be eliminated, the engine requires replacement.

Control module problems

The control module is the “brain” of the machine. This is one of the tricky parts. Some defects are noticeable to the naked eye and can even be eliminated on your own.

For example:

• condensation that has appeared and requires drying;
• dark spots - they can be wiped off with an alcohol-containing product.

It is best to entrust a specialist to carry out high-quality diagnostics and troubleshoot problems in this element, since correction requires not only special skills and knowledge, but also a suitable tool.

You can see how the module’s state is analyzed in the video:

Trouble-shooting

If a particular model does not have a display, or an error code is not displayed, you need to carefully listen to the operation of the device. When the bearings wear out, you should be alerted by the loud noise of the operating machine.

It is better to entrust the repair of washing machines to professionals!!!

We present to you our unique catalog of private masters and service centers - BigWash.ru

Select your city and artist in the filter: by rating, reviews, price!

If there are no obvious signs of malfunction, the machine will have to be disassembled.

Replacing the motor sensor and surge protector

Failure of the surge protector is one of the most common failures. This is due to the high concentration of moisture.

To remove the filter, you need to remove the top cover and unscrew the fixing screw. When installing a new filter, you can treat the contacts with silicone sealant - this will help solve the moisture problem.

If the tachogenerator fails, then the cause is most likely a burnt capacitor. It is not difficult to replace it with minimal electrician experience.

If replacing the capacitor does not solve the problem, it means that the engine sensor itself is faulty; it cannot be repaired, it can only be replaced.

Replacing the heating element

If the water does not heat up, the hatch is cold, the powder does not dissolve, this means that the heating element is not functioning. First of all, you need to remove the back panel of the case. Under the tank you can see two contacts of the heating element; you need to remove the wiring from them and take measurements with a tester. If the resistance is within 20-45 Ohms, then the element is operational.

If the tester shows a short circuit or break, the heating element will have to be changed.

If, despite normal readings from the device, the water still does not heat up, you need to unscrew the fastening bolt, remove the seal and pull out the heating element. The presence of a layer of scale and dark burn spots indicate that the heating element needs to be replaced.

Watch a video on removing and replacing the heating element of an Indesit washing machine:

Complications with the bearing and control unit

Replacing a bearing is a simple operation, the difficulty is getting to it. If the tank of the car is made as a single piece, it is impossible to disassemble it. The only solution in this case is to saw along the weld seam.

When the rear wall of the unit is detachable in order to access the bearing, the machine can be disassembled. How to do this and replace the bearing is shown step by step in this video:

https://youtube.com/watch?v=uFpLe_Kd0NE

The control unit is structurally poorly positioned; accumulating condensate affects its operation. Contact closure due to high humidity leads to controller failures. To repair, you need to carefully ring all contacts with a tester and clean the faulty ones.

Kandy washing machine errors without display

To read errors on a washing machine without a display, you just need to count the number of flashes. Here the following must be taken into account: if a code starts to appear, the indicators blink at intervals of 0.5/1 second, and the interval between the end and the beginning of the error lasts about 5 seconds. So that you understand what happens next, for example, let’s take a code with five flashes, that is, the indicators blink 5 times, then a 5 second pause and again they should blink 5 times, then again a 5 second pause, repeating about 10 times. I think I explained it clearly, now you can sort out all these codes in order. Photo of a Kandy washing machine without a display

You put things in the drum and started the program, but after a while you discovered that the Kandy washing machine stopped washing, did not spin the drum and displayed code E08 on the display. Before stopping, you may have observed one of the following signs:

• the drum of the machine rotated for a short time at high speeds (right with water immediately after turning it on);
• the drum rotated only in one direction - clockwise or counterclockwise;
• The SMA did not rotate the drum at all - error 8 came on almost immediately.

How to determine the error code on cars without a display

Outdated Indesit models have a built-in EVO-I control system. However, they do not have a display to display information. But, nevertheless, they are able to report errors that have arisen in the system. They can be identified by blinking indicator lights. For example, flashing rapidly five times with a break of several seconds indicates error code F05.

In vehicles equipped with the EVO-II control system, the method for determining codes is slightly different. After all, each model has different functionality. And this makes it difficult to read errors. To understand the fault code, you need to understand what this or that indicator indicates.

The following types of indicators are distinguished:

• timer – kn1;
• super wash – kn2;
• quick wash – kn3;
• additional rinse – kn4;
• spin – led4.

Now let's look at how to read the meaning of indicator signals.

Designations on typewriters: WISL, WIUL, WIDL, WIL, WITP

These washing machines signal breakdowns in the system by indicating special function buttons and a “Spin” light. To help you determine the malfunction, you should focus on the serial numbers of the buttons when recalculating them from left to right, and not on the names of the functions. Since the latter may differ due to changes in the control panel on the listed machine models.

Any error code will be accompanied by constant rapid flashing of the “Lock” indicator, which is responsible for blocking the hatch door.

So, in the list we will indicate exclusively the numbers of indicators that flash during a particular malfunction:

• F01 (F1) – 4;
• F02 (F2) – 3;
• F03 (F3) – 3 and 4;
• F04 (F4) – 2;
• F05 (F5) – 2 and 4;
• F06 (F6) – 2 and 3;
• F07 (F7) – 2, 3, 4;
• F08 (F8) – 1;
• F09 (F9) – 1 and 4;
• F10 – 1 and 3;
• F11 – 1, 3 and 4;
• F12 – 1 and 2;
• F13 – 1, 2 and 4;
• F14 – 1, 2 and 3;
• F15 – 1, 2, 3 and 4;
• F16 – the indicator Cycle 4 (“Spin”) blinks;
• F17 – lamp 4 and cycle indicator;
• F18 – button number 3 plus spin indication.

The Indesit washing machine without a display clearly informs the user about a breakdown that has occurred. A clear display will unmistakably indicate any malfunctions that have occurred in the system.

Error codes indesit w 105 tx

The displayed fault codes for Indesit washing machines are presented in Table 1.

Table 1 - Errors, their names and possible causes

As can be seen from the table, for each error information there are several reasons for its occurrence. And as a result, the light warning shows the direction in which to start troubleshooting, which significantly saves the time of service workers and reduces the time the washing machine is under repair.