How to plug a hole in the bathroom instead of a plug? How to make a bathroom stopper with your own hands? How to buy a stopper and siphon for a bathroom on Aliexpress: links to the catalog

A stopper, plug or plug in the bathroom (as this product is called by different users) is needed in the bathroom. Without it, it is impossible to draw a bath, soak in the fragrant foam or rinse the laundry. If for some reason this part is missing in the house, it can be replaced with improvised means or made with your own hands. Tips and recommendations from home craftsmen will help solve the problem of plugging a bathtub instead of a stopper.

How to plug a hole in the bathroom instead of a plug?

There are many ways to plug a bathroom drain. Most often, such devices are sought by those whose old plug has broken or who urgently needs to take a bath in a rented apartment. Otherwise, it’s easier to buy a stopper at a hardware store, since the product costs a penny.

Bathroom plug options:

Plastic bag. You need to take a clean plastic bag and fill it with cloth. The patch should be small and only slightly larger than the size of the drain hole. You need to fold the fabric and put it in a bag. After this, the cellophane must be tied and placed in the drain hole. Now you can open the tap and fill the bath. The resulting nodule will be sucked into the hole, where it will remain until the end of the bath.
Foil. This is a one-time option, so it is suitable if you urgently need to close the drain hole, but there is nothing else at hand. In this case, you need to take a decent piece of foil and crumple it. After this, the lump is inserted into the drain hole.
Cup. It is best to use a plastic glass for these purposes, since a glass container can break into pieces if it hits a metal bathtub. The glass must be installed upside down.

How to plug a hole in the bathroom instead of a plug?

Squeeze out the plug, creating increased pressure inside

Place the bottle of wine at an angle in a pan of water so that the stopper is above the water. Heat over the fire until the cork begins to crawl out. We pull it out by hand.
Similar to the above method, we place the container on the firewood, light it and wait for the plug to “crawl out”.
You can heat the neck just below the cork with a lighter, or better yet, two lighters on different sides.
Using a syringe. Take half a glass of drinking water, pierce the cork with a needle (it is better if it is thick). We fill the syringe with water and pour it into the bottle. And so on all the water. (Don’t be afraid - it won’t mix with the wine!) Pull out the creeping cork with your hands, drain the water - a little more than half a glass. Ready!
A pump for a volleyball or soccer ball with a needle will also help. We insert it into the plug and very carefully pump air into it. Be very careful!

How to make a bathroom stopper with your own hands?

There are a lot of options for making a bathroom plug. Handymen who cannot sit idle for a minute love to get involved in this activity.

DIY bathroom plug:

Flip-flop. Old shoes with foam soles are very suitable for making cork. It is necessary to cut the plug to the size of the drain hole with a stationery knife. Next, you need to tie a rope or chain. This plug fits perfectly into the drain hole and water does not leak out.
Wine corks. You need to connect several wine corks together. In this case, you need to cut them so that there are no voids or holes left between the pieces. Then the resulting circle is adjusted to the size of the drain hole. You can fill everything with silicone and let it harden.
Tree. It is very easy to cut a chopstick from wood; it should exactly match the diameter of the drain in size. For a better fit, you need to grind down the edges so that they are perfectly even.
Salt. Well, this is an emergency method. You need to pour a little salt into a sock or small fabric bag and put it in the drain hole. Such a homemade plug will be sucked inside, which will prevent water from spilling out.
Styrofoam. If you still have foam packaging from the equipment, you can use it to make a plug. It is necessary to cut a circle according to the size of the drain hole and place it inside.

How to make a bathroom stopper with your own hands?

If the tongue is jammed ↑

Most locks are equipped with a special spring-loaded latch. If the spring fails, the tongue stops moving and supports the door leaf. To release it, the part must be squeezed out or simply moved aside. The easiest way to do this is from the side where the door opens.

Any flat and thin object will come to our aid: a rounded table knife, a thin chisel, a ruler, a flat screwdriver, a plastic card, etc.

We insert the tool into the gap between the jamb and the canvas in the place where the tongue is located.
We tilt the tool towards the door handle while pressing it. If everything goes correctly, you can feel the tool sliding along the cut of the tongue.
Now you need to press it away from you so that the tongue can go into the lock. Pull the door towards you or push it, depending on where it opens.

If you have to open the structure from the side where the tongue does not have a cut, insert the tool from above. Then we tilt it diagonally to reach the inside of the lock. Now press the tongue firmly.

You can open the door without a key using wire or hairpins

What can you use to make a bathroom drain plug?

You can make a drain plug from improvised means and available materials. Very often, children's toys, in particular balls, are used as corks.

Materials for making a bathroom stopper:

Silicone. The manufacturing method is quite simple. It is necessary to place a bag in the drain hole and pour silicone into it. It is necessary to level the silicone with a plastic spoon. The silicone will take the shape of the drain hole. After hardening, the cork can be removed from the cellophane shell. If desired, you can put shells or stones inside. Don't forget the chain or rope.
Wood. Not the best option for making cork. But if you have no choice and need to plug the hole with something, you can use a piece of wood. Cut a cylinder to the shape of the drain hole.
Rubber. This is an excellent material for making plugs. It is soft, easily compressed and molds to the shape of the drain hole. It is necessary to cut a cork of a suitable size from a piece of rubber.

What can you use to make a bathroom drain plug?

Temporary covers

For a temporary jam you can use:

A piece of foam, cut to fit the drain hole.
The fastest, but also the most short-lived way to make a bathroom stopper is to crumple up a newspaper or sheet of paper. You just need to push the paper very tightly so that the homemade plug lasts longer.
You can make the method a little more complicated: stuff the paper tightly, giving it the desired shape, then dry it, and then tie the bags, removing air from them as much as possible.

Important! You need to use 3-4 bags to block the access of water to the paper, then the seal will last longer.

For a while, you can plug the hole with whatever you have on hand, for example, a sock or even several if one is not enough. Simply scrunch one or more socks into a ball and stuff them into the hole.
You can fill a sock with fine salt or sand and wrap it in a plastic bag on top. Pour the filling into the sock in a small amount. Thanks to them, the sock will take the desired shape and reliably hold water in the bath.
If you have foil on hand, crumple it into a ball and cover the drain hole with this ball. The size of the ball should be slightly larger than the hole in the shell itself. This lid holds water well, but it is disposable.

Important! You should not use this method regularly; it will cost you more than just buying a new plug.

You can fit any children's toys of a suitable size under the cover. But, of course, they must be made of material that does not allow water to pass through. For example, it could be a ball of suitable diameter.
Wrinkle a sponge for washing dishes, put it in a bag and insert it into the drain hole - the temporary plug is ready.
Cover the outlet with a plastic cup or a wet rag folded several times.

How to buy a stopper and siphon for a bathroom on Aliexpress?

of siphons and plugs for bathtubs on sale. Models differ from each other not only in shape, but also in material.

Siphon design:

Bottle type. This is a familiar design that resembles an ordinary bottle located below the pipe. It turns out that under water pressure, debris can settle in this container. The main advantage of such a siphon is the ability to quickly clear the blockage. Such siphons prevent clogging of the sewer and riser. It is enough to periodically clean such a siphon and remove accumulations of fat, hair and waste from it.
Pipe. This is a structure consisting of several tubes. All the debris settles in the elbow, that is, in the curved tube.
Flat. This is also a tube system in which the water seal is represented by a horizontal tube. Under the influence of water, particles settle in this horizontal tube. To clean the system, simply remove and wash the horizontal tube.
Corrugated. These are ordinary corrugated tubes, wound several times. The cheapest option, which quickly becomes clogged due to the relief of the tubes.

To make your first order on Aliexpress , read the instructions for registering and searching for goods, payment and delivery on the official website here , or read the article on our website “First order on Aliexpress” .

Aliexpress is a universal site where you can purchase many household goods.

These are in the Aliexpress catalog : siphons, stoppers and bathroom fixtures .

Now on the site there is a huge number of cheap and exquisite bathroom items.

Now a bathroom stopper is not just a piece of rubber, but a real work of art.

How to buy a stopper and siphon for a bathroom on Aliexpress

As you can see, making a bathroom stopper is very simple. To do this, you do not need to know how to work with carpentry tools. If necessary, you can close the drain using a regular glass.

Problems

It all depends on its material and design.

The easiest way to do this is with a rubber plug: you just need to pick it up by the edge with a flat-head screwdriver.

This also applies to a metal plug with a rubber shell.

You can try to remove the plastic plug with the same screwdriver, alternately prying it from different sides.

If this does not help, a corkscrew for wine bottles can often save the situation: it is screwed into the cork, after which it is removed with some effort. Of course, after this you will need to go to the store to get a replacement for the damaged part.

Finally, if the corkscrew turns out to be powerless, you have to take radical measures: the cork is drilled in the middle and removed with pliers.

The biggest problem that can cause the owner is a brass plug stuck in the outlet of an old bathtub. Especially if the eye for the chain, which can be caught with pliers, is broken off. Sometimes it is possible to grab its edge with a gas wrench. If the key slips, you have to disassemble the outlet and knock out the plug from below, which is extremely inconvenient due to the tightness under the bathtub.

The worst case scenario is dismantling the cast iron outlet. In this case, it is easier to change the entire harness.

As a rule, cast iron trims are equipped with brass plugs. Here are some recommendations for dismantling them:

If the semi-automatic piping drive or the piping latch breaks down, the plug will also remain in the outlet. You can try to swing it with a plunger and pry it off with a pair of screwdrivers or knives.

If for some reason you don’t feel like checking out local plumbing stores, but have a tube of silicone sealant on hand, the instructions will be quite simple:

Any object can be cast from sealant. You just need to make a mold.

If your bathtub outlet has a stainless mesh that protects the drain from hair and other debris, place a plastic bag under it. It will ensure the release is tight, and the mesh will prevent it from floating up.

The photo shows an improvised plug made from a mesh for release and a plastic bag.

Here are some of the most obvious solutions:

The outlet grate can be plugged with any suitable object, as long as it does not allow water to pass through.

Stationary

Another name is that capital screens are non-removable panels. The closed part at the bottom of the bathroom makes access to the basement difficult. It will be very difficult to install the product yourself, so it is better to trust the professionals. These models are a structure that requires additional finishing. Such screens are usually made from the following materials:

chipboard;
moisture-resistant plasterboard;
brick;
board;
plywood.

Stationary screen
Once the material has been selected, the panels can be finished in any style. If you wish, you can paint them yourself or use tiles instead of paint, which is very convenient. In addition, it is possible to use film, PVC panel or artificial stone as a finishing material.

Brick options

Brick models are the most reliable foundation, they are distinguished by an affordable price, as well as ease of construction, which can be done with your own hands. The one-piece design consists of laying bricks with cement mortar, which provides the screen with reliability and strength. Facing is carried out with any material available for this purpose. The enclosed space will look attractive, and uneven masonry can be corrected with the amount of glue during finishing.

Advantages of an automatic system

The operation of the device begins by pressing without the use of additional devices. There is a hidden button inside the cork that is not visible to outsiders. Nowadays, you can choose automatic bath plugs depending on your bathroom design. In addition to the advantages, the devices also have some negative aspects.

High price of the product and its repair. Automatic devices cannot be purchased separately, as they are part of the siphon system. If the automatic plug fails, the siphon is completely replaced.

Breakdown frequency. Devices can often break down, especially for low-quality units. Failure may be caused by wear of the spring that drives it or wear of the rubber seal.

To prevent breakdowns, it is worth choosing in favor of well-known companies producing plugs. The best and highest quality bathroom stoppers are made by the German company IKEA.

Common people call this another negative aspect of using automatic devices. They begin to work only when pressed with a hand or foot that is immersed in water. But this is difficult to do if very cold or boiling water is poured into the bathtub.

Variety of devices

Many people want to relax and lie in warm water, so that it does not flow out of the bathroom; they should buy a stopper, which is used to close the hole in the pipe. This may be a device with a chain, familiar from ancient times, or it may be a modern device of a semi-automatic or fully automatic nature.

Outwardly, a cone-shaped device familiar to ordinary people, which helps close the hole from the bathroom, is a mechanical plug. It is usually made of rubber, plastic or metal material.

With this device, the drain is reliably and firmly closed. Moreover, it cannot fail. Unfortunately, sometimes the plug can get stuck inside the hole.

More modern mechanisms are automatic and semi-automatic bathroom plugs. The first device begins to work after a simple press made by hand or foot. The operation of the semi-automatic device begins with pressing the lever.

Bathroom drains and overflows - types and features

The simplest type of design is considered to be a standard overflow drain: water is drawn into the bathroom with the plug closed, and drained, accordingly, with the plug open. These are the kind of drains that were previously installed in any bathtub and were found in almost every apartment.

There are also more original products - they are made for bathtubs of non-standard models, but automatic and semi-automatic overflow drains are in greatest demand, and we will talk about them in more detail.

Semi-automatic drain – design features and advantages

Semi-automatic drain mechanism A
semi-automatic bathroom drain differs from other types of this useful mechanism in that the plug closing the lower drain hole is opened using a cable that connects the drain and overflow block of the device. Thus, when using the bathtub, it is enough to slightly turn the overflow cover and the drain will open (or vice versa close).

A semi-automatic machine is very convenient, because now, in order to start drawing water into the bowl, you don’t have to bend over each time and close the drain hole with a stopper. In addition, a semi-automatic bath overflow drain visually looks more attractive than simplified design analogues. A semi-automatic drain in the bathroom has only one drawback: with intensive use of the device, the cable may begin to get stuck and jam. There are models in which the cable is located outside rather than inside the structure, but in appearance they are significantly inferior to models with a hidden cable.

Advice: when choosing a semi-automatic bathtub drain, do not save money and buy a more expensive model made from really high-quality materials.

Household chemicals

In fact, you can unclog a bathroom clog without a plunger. After all, you can simply purchase modern cleaning products.

If previously only soda was used for this, today it is enough to visit the household chemicals department and choose the packaging you like.

It is best to choose a product whose instructions indicate that it dissolves hair and fur.

Recommendations:

You can choose not only a special cleaning powder, but also a liquid product.

It is necessary to clarify in the instructions that the selected product is really suitable for a specific type of sewer pipe.

The product must be carefully poured or poured into the drain hole. If it is a special powder, you should also add a glass of warm water.

To be sure to remove the clog, you need to avoid using the bathtub for a while.

After a certain period of time specified in the instructions, it is necessary to turn on the hot water in order to thoroughly rinse the sewer pipes and remove debris.

Instructions for repairing through damage (cracks, holes) in acrylic bathtubs

In order to repair a hole in the bathtub you will need: - a drill with a drill Ø2-3 mm; - abrasive wheel; — repair kit for cosmetic repairs of acrylic bathtubs; — repair kit for major repairs of acrylic bathtubs; — sandpaper No. 100, 200, 400; — universal putty (epoxy, “pe brulex”, etc.); — bath enamel (“stakryl”, “epoxin”, “tikkurila reflex 50”, etc.); — reinforcing tape with glass fiber; - alcohol.

Drill holes with a diameter of 2-3 mm at the ends of the crack. This is done in order to prevent their further development. Clean the damaged area with 100-grit sandpaper and degrease it with alcohol.

Mix the resin from the repair kit for the overhaul of acrylic bathtubs with the hardener in the proportions specified in the instructions. Apply a layer of resin to the repair area. Apply reinforcing material over the resin. Press it into the resin and apply a second layer of adhesive on top, ensuring that it saturates the material and penetrates all the pores. Wait until the resin hardens. The waiting time is specified in the instructions for the repair kits. Some of them require the application of several layers of reinforcing material. Follow these requirements.

After all layers have been applied and hardened, sand the repair area first with No. 200 sandpaper, then No. 400. Make sure the treated surface is as even and smooth as possible.

Treat the repair surface with alcohol and apply polish from the repair kit for cosmetic repairs of acrylic bathtubs. Polish the repair area with flannel.

Repair of through holes in cast iron and steel bathtubs

If the hole in the cast iron bath looks like a crack, drill holes with a diameter of 2-3 mm at its ends with an electric drill. You don't have to do this in an iron bath.

Treat the damage with an electric drill and an abrasive wheel so that a crater-shaped crater forms around the damage. The damaged area must be cleaned to bare metal. The larger the chamfer of the funnel and the flatter its edges, the better.

Degrease the repair area with alcohol. Mix universal putty based on epoxy resins with the hardener in the proportion specified in the instructions. Apply the mixture to the edges of the damage. Apply fiberglass reinforcement tape to the damage, pressing it firmly to the surface. Apply another layer of putty over the tape. Give it time to harden a little. Repeat the operation with the application of reinforcing tape again. When covering it with resin, try to keep the surface of the damage slightly higher than the surrounding surfaces of the bath.

After the resin has completely hardened, sand the damage first with No. 100 sandpaper, then with No. 400 sandpaper. Try to ensure that the surface of the damage is flush with the surrounding surface. Degrease it with alcohol and apply one of the bath enamels (“stakryl”, “epoxin”, “tikkurila reflex 50”, etc.). Since the technology for applying enamels may be different, follow the instructions for the specific material.

Hot water with salt and washing powder

Kitchen sinks most often become clogged due to a layer of fat accumulated in them. You can remove it simply by removing fat from the walls. For this:

Mix half a glass of salt and soda;
Pour the mixture down the sink drain;
Pour a glass of hot water over this.
After some time, the fat will dissolve and the clog will go away. For plastic pipes, it is recommended to use hot water and washing powder.

By the way, read this article too: Glue gun: what can be glued, types of consumables, characteristics of popular models

Cable

Plumbing cable is a thick twisted wire, rolled into a small spiral. For convenient rotation, there is a handle with a wooden or plastic attachment at the end.

This device is actively used to remove sewer blockages. Moreover, we are talking mainly about metal pipes.

Application:

The end of the cable must be carefully inserted into the drain hole.

It is best to do the work together. So, one person slowly rotates the handle, and the other carefully pushes the cable forward.

When the cable is twisted, accumulated debris is removed from the pipes, that is, the blockage is destroyed.

As soon as the tension in the pipes decreases, you need to pull the cable back and forth several times.

The cable is carefully removed, washed and stored.

If the procedure is ineffective, it is repeated.

Before removing the blockage, you need to pay attention to the tension of the cable. Lack of tension can damage the cable.

Classification

When purchasing a seemingly ordinary thing - a plug for a sink, you need to take advantage of a number of observations.
They are shaped like a truncated cone, and are also made from various materials and take different sizes. These simple devices are necessary to shut off the drainage hole, used and no longer needed, dirty running water.

Mechanical jam

It is a bathroom stopper with a chain, made of plastic, rubber or metal and coated with a thin layer of a substance that protects the product from corrosion.

This is the oldest of all devices, but it is the most reliable, on a par with the latest mechanisms, which at any time can become unusable.

Automatic plug

A more modern thing, activated by light pressure from any part of the body. This is very convenient, since you don’t have to think about how to remove the bathroom plug, because you don’t even have to bend over, making extra unnecessary movements.

Semi-automatic stopper

This bathroom drain stopper will allow you to close and open the damper using a lever, button or small handle without direct contact with the object.

Self-production

Force majeure happens when something needed at the right time is lost. In such unpleasant moments, you have to use all your ingenuity to find a way to solve the current unforeseen circumstances.

In this case, you can improvise by independently turning into reality a prototype of a universal bathroom stopper from scrap materials found in the dusty corners of the house.

Of course, for one single case you shouldn’t invent an airplane, but hastily build something similar, but you can, of course, be original by working on an entire work of art.

Temporary bushings

For one-time use, you can take a piece of foam and cut it to size. There is another technique, but it is less durable - this is a sheet of crumpled newsprint, pushed into the hole in dense layers to avoid leaks.

You can also tie a plastic bag around the crumpled sheet, tying it in a knot and sticking it into the passage - this will be a more long-term option compared to the previous variation.

But there is an option to spend a little more time to try to create a more durable option.

How to make a bathroom stopper from a piece of wood? It’s very simple, first take a ruler and measure the diameter. Then transfer the marks to the wooden beam. The next step will be cutting to the diameter and processing the material with sandpaper.

Next, all that remains is to saturate the product with a hydrophobic chemical so that it repels moisture, preventing the log from swelling.

A beautiful lid with an unusual antique-style design will be made from wine corks connected together, but try not to leave gaps between them. This design can be covered with special glue or filled with epoxy resin - this will create an unsurpassed effect and a pleasant smooth surface.

No matter how funny it may sound, a plug made from old flip-flops will come out very airtight if you can carefully cut the rubber exactly to the shape.

What it is

An air lock in the sewer is one of the types of technical blockage in the pipeline. Most often, this is a bend (“hump”) in a section of the pipeline within which air collects. Waste liquid cannot pass through this unit, especially if it carries a large amount of organic matter, suspended matter or other components. They accumulate in front of the problem area, forming a continuous blockage. At the same time, there are no mechanical obstacles to the passage of wastewater, only an air bubble.

Sometimes a complete blockage does not occur; the drainage gradually passes through the channel. However, you have to wait until the waste comes out of the toilet flush, the dirty water comes out of the kitchen sink or from the bathtub. All attempts to push the liquid using a plunger or cable are unsuccessful, since you have to act blindly, not knowing the exact cause of the problem.

Until the sewer system is repaired, the air lock persists and continues to cause a lot of inconvenience. By itself, it will not disappear anywhere, since there is a physical phenomenon taking place here. As long as there are conditions for its existence, the defective area will exist. Over time, the problem will increase due to accumulating waste, fatty deposits, and organic matter. A section appears with a reduced cross-section of the channel, where the drains lose speed. Suspended particles settle to the bottom, little by little forming a regular clog. It is cleaned, but since the air bubble has not disappeared, the problem occurs again.

Ready-made models

The factory screen under the bathroom is often already equipped with a curtain, which makes access to communications easier in case of unforeseen circumstances, and also allows you to store cleaning products or tools. This method is rightfully considered the most common, and besides, it will cost no significant costs. These products are usually made from plastic material, however, there are also metal, glass, and wooden variations. The dimensions of the structure fit the dimensions of the bathroom.

Ready bath screen

Finished products can be easily installed and secured with your own hands. They consist of one or more panels equipped with a curtain. The entire structure is framed with a metal or aluminum frame on special legs. The screen under the bathtub is attached to the floor at an angle of 90°, after which the legs are fixed to the floor. This model allows you to completely close the space under the bath. Kinds:

sliding curtains;
closed tightly;
swing doors;
drawers.

Deaf

These products are tightly closed structures, not equipped with a curtain. They are able to completely close the space below. They are distinguished by the type of panels: solid or lattice. After installation of the structure, the spacer legs can be loosened, and the screen itself can be removed in case of urgent need. Thus, constant use of the basement space will be difficult.

Cleaning the toilet with a cloth

Wrap a floor rag around a stick and plug the clogged hole with it. Then, with a sharp up and down movement, break through the blockage using the resulting water hammer.

Manual cleaning

If the drain is a structure with a siphon, then it can be cleaned manually. To do this, you just need to unscrew the siphon, remove the debris, wash it and put it back on. You can also try cleaning the drain yourself using the following methods:

Thermal: use of hot water;
Chemical: the blockage is removed using certain compounds;
Mechanical: special devices are used to solve the problem.

Sole piece

Simple beach flip-flops usually have foam soles that are resistant to moisture. If you have an old pair of shoes in the house that you don’t mind ruining, then this method will work. You can cut a circle of the desired diameter from the sole of one slipper. The result is a reliable cork that is suitable for repeated use.

Choice

Varieties

What types of traffic jams are there??

Traditionally, this is a simple plug in the shape of a truncated cone, made of plastic, brass or rubber.

Brass plugs were used to complete cast iron bathtub fittings that were produced more than three decades ago. Nowadays they are found only in apartments of old houses, in which the plumbing has not changed during the entire period of their operation.

A metal chain (brass or stainless steel) is attached to its eye, with which you can remove the cork without getting your hands wet. However, some fittings (the so-called set of drain fittings for a bathtub) are somewhat more complicated:

Trim - the machine allows you to open and close the drain by simply pressing it with your hand or foot;

Release of automatic strapping.

Semi-automatic piping makes it possible to open and close the outlet from the bathtub by turning the decorative handle on the overflow.

Comparison

Which harness is more convenient and reliable??

In terms of convenience, in my opinion, the leader is the semi-automatic harness. Automatic plugs are less convenient, if only because the drain cannot be opened without getting your hand or foot wet. This is especially inconvenient when the bathtub is full of hot or ice water.

In terms of reliability, an equally undisputed leader is a harness with a separate plug on a chain. It is reliable precisely because it is extremely simple in design. Both competing solutions have their own vulnerabilities:

For a semi-automatic plug, this is a cable connecting it to the handle on the overflow. After some time of use (usually 2-3 years), it begins to jam;
For an automatic plug, the cause of failure is a breakdown of its fixation mechanism. It is not sold separately from the harness, which makes the maintainability of the entire structure zero.

The price of a plastic harness with a separate plug usually does not exceed 350 - 400 rubles. Metal strapping - a semi-automatic machine will cost the buyer at least 1,500.

Inexpensive and extremely reliable design.

Which material is better - plastic or rubber??

Decorative curtain

Using a curtain, you can securely close the basement space with your own hands. This method is rightfully considered the most accessible, simple and cheap. It perfectly hides imperfections under the bathroom, disguises unattractive places, and, in addition, makes it possible to safely store all the necessary cleaning products and equipment.

Decorative curtain
The curtain is easy to care for, i.e. she is unpretentious in everyday life. It is enough to pick up an ordinary piece of cloth and wipe it periodically. In addition, the fabric can be useful for placing the curtains around the perimeter and fastening them together. This will compact the material, making it more durable and practical. Usually special folds are left, but you can do without them.

Folk remedies for dealing with blockages

To clean a sewer pipe, use improvised means that have an aggressive effect on organic contaminants. Substances in this group cannot dissolve synthetic waste. The advantage of this method is considered to be ease of implementation, since in most cases the necessary funds are available in the house. In addition, their use is environmentally friendly: no toxic substances are released during use, and no harmful effect on humans is observed.

The disadvantage of the method is considered to be low efficiency. If a pipe is clogged, folk remedies will not be able to remove severe contamination. The most effective options:

Lemon juice is used for mild stains.

Vinegar + soda. The components are taken in equal quantities, and it is important to use no more than 1 glass of each of them in one go. First of all, you need to remove the water from the sink/bathtub. If this is not done, the product will not help, because when using it, the chemical reaction between the components is considered the most important. First, pour soda into the drain, then immediately pour in vinegar. To enhance the properties of such a mixture, the hole is tightly closed. After 3 hours, you need to clean the drain using hot water. This will remove any remaining chemicals and contaminants.
Lemon juice. This option is not strong enough to eliminate the manifestations of complex congestion. For this reason, it is used when mild contamination appears, for example, if water does not leave the drain for a long time, but its slow movement through the pipeline is observed. You need to pour the fresh juice of 3 lemons into the hole of the bathtub or sink. The product is left for 1 hour, after which the sewer system is washed with running water.
Boiling water. This option is only suitable if the jam is caused by organic contaminants, such as fatty components. Under the influence of high temperature, the fat dissolves, the cork is destroyed partially or completely - it all depends on what kind of debris it contains. In terms of implementation, this option is simpler than other methods: you just need to open the hot water tap and wait for the pipe to clear.
A solution of soda and salt. In terms of effectiveness, this option is not inferior to methods based on the use of lemon juice or hot water. Mix 500 g of soda and 200 g of salt. You need to prepare a solution, for which the components are diluted with water (1 liter) and boiled. Water is removed from the plumbing fixture, then the finished product is poured into the hole. The solution must be hot. The drain is closed to improve the result. After 2 hours, the substance is washed out of the pipeline with hot water.
Caustic soda is also a good tool for cleaning pipes; it works more effectively than the considered analogues. It is not recommended to use the substance in dry form. A solution is prepared on its basis: 200 g of caustic soda, 1 liter of boiling water. The product is poured into the hole in the sink/tub. After 2 hours, the pipeline must be flushed.

A solution of caustic soda with boiling water is poured into the sink hole, then after 2 hours you can rinse the water supply.