Everyone knows how good WD-40 is. I knew too, but somehow there was no need to use it, since I had not yet had a chance to turn the soured nuts on the car. But now I also have this magical remedy...) And it was like this. The oven light burned out. The first thing to do in this case? That's right, take it out and buy the same one. The oven is new, it’s not even three years old. There is a glass lamp above the light bulb that needs to be unscrewed. It is logical that it did not sour and did not become particularly smoky in such a short period of time. But! They twisted it, making incredible efforts, the whole family twisted it, twisted it until they became blisters for three days.))) The lamp did not give in even a millimeter. My fingers hurt and the toad is choking me. I go to the auto store and buy WD-40.
One spray around the lampshade.
Voila. With a slight movement of the hand, the lampshade is unscrewed.
Customer service, Packaging and used device
Page 32
- Image
- Text
Customer Service
E number and EO number
If your device needs repair, our Customer Service is always at your service.
Address and telephone number of the nearest workshop
You will find it in the telephone directory. IN
service centers specified in this
Management will also give you the address
the nearest workshop.
When calling Customer Service, always indicate the product number (E-number) and
serial number (EO number) of the device. The nameplate with numbers is located on the right, on the side of the oven door. So as not to search for a long time
numbers in case of malfunction, enter the device data right now.
Number E
EO number
Customer service ®
Packaging and used device
During transport of your new device
protected by packaging. All packaging elements are environmentally friendly and can be reused.
Help protect the environment by throwing away packaging.
In turn, used devices are not at all
are useless waste. If properly disposed of, they can serve as valuable raw materials.
for processing.
Before disposing of a used device,
make it so that it can no longer be
use or mark it with a sticker “Attention, scrap metal!”
You can get information about the opportunity
recycling at your dealer or local
administration.
32
HOW TO REPLACE A LIGHT IN AN OVEN OVEN
HOW TO REPLACE A LIGHT IN AN OVEN OVEN
Replacing an oven light bulb is not without difficulty.
In the process, the most important thing is not to touch the fragile cap. The instructions for replacing the lamp must be followed carefully. This approach will ensure long-term operation of the device. Lamp replacement process
Lamps in gas and electric stoves are changed in a similar way to each other. However, the replacement process in different models may be carried out differently. First you need to turn off the oven itself. Allow it to cool, especially after cooking. The warmer the oven itself, the more difficult it is to unscrew the lamp and cap. The last element must be unscrewed before the lamp itself. The faulty lighting device also needs to be removed. Check the owner's manual for your oven to determine which appliance is compatible with your oven. Only after familiarization can you buy a new lighting lamp. Then install it together with the cap. Check the lamp's functionality. There are times when a suitable lamp is not available for certain ovens. In this case, try to avoid damaging the lighting fixture and be more careful with the equipment.
Electrolux
Ovens of the brand in question interact differently with lighting lamps. Electrolux stoves have removable glass. And it is attached with a latch. To remove it, light pressure with a screwdriver is necessary. The disconnection will occur and the part can be pulled out. Then unscrew the old lamp and connect the new one.
Bosch
You can replace the lamp in two ways: 1. Replacement method, as in Electrolux ovens; 2. By partially disassembling the oven; In case of disassembling the oven, you must contact the service center.
Hansa
Replacing the lamp in ovens of this brand occurs according to the standard process: 1. Unscrewing the cap; 2. Removing the cap; 3. Unscrewing the lamp; The cap in Hansa ovens has ridges. By holding them you need to unscrew the device. If you lack strength, press the rag against the cap. After turning, the cap is removed in a forward motion.
The most suitable lamp for most ovens
Most often, devices with an E14 base are used. This type of base is available for halogen and incandescent lamps. The manual for the oven of a particular model must specify which base is most suitable. There are cases when the slab interacts only with a smooth base. Lamps with powers of 25W and 40W are usually used. The main differences between them are power consumption and backlight power. They also differ from each other in service life: 1. 40W - 2-5 years; 2. 25W - eternity; Typically, for simple cooking in the kitchen, 25W lamps are chosen. For baking or other similar processes that require long-term baking, you need to buy 40W lighting. Backlight lamps must withstand heating up to 300°C and above. The packaging of the lighting product indicates the set temperature. This also applies to halogen lamps.
You need to be careful with halogen lamps because of the mercury inside. If a light fixture breaks, immediately pick up the pieces. Otherwise, mercury may end up on the food being prepared. It is more convenient to collect fragments using a brush. After you have collected the fragments, you need to throw away the brush. Treat the surface with potassium permanganate from a spray bottle. This will make the halogen lamp burn brighter than before.
Conclusion
When replacing a light bulb, you need to be very careful. There is a risk that the glass will break or deteriorate to such an extent that the device may no longer be suitable for further operation. To find out whether the lamp is suitable for your device, carefully read the operating instructions. Each manual tells you what type of lamp base the correct lamp has and how to install it correctly.
Article
Typical Lamp Replacement Procedure
For any electric and gas stove, the lamp in the oven changes in a similar way.
Depending on the models, replacing the oven lamp may differ from the general procedure. She is like this:
- Turn off the power supply to the oven.
- Turn off the oven and let it cool completely. If this is not done, the cap and lamp will be difficult to unscrew due to thermal expansion of the metal.
- Remove the lamp cap by unscrewing it or releasing the latch.
- Unscrew or remove the faulty lamp.
- Read the operating instructions for your oven: what kind of lamp, what power, voltage and with what base is installed there.
- Buy a light bulb for your oven.
- Install the lamp and cap.
- Check the work.
Sometimes older ovens use a special lamp that can be difficult to find commercially. Keep this in mind and avoid actions that could damage the lamp, otherwise your oven will remain without lighting.
Lighting in the oven
Electrolux ovens
The Electrolux oven lamp is installed slightly differently. There may be installation in the manner described earlier, with a threaded cap, but most often Electrolux models have installation with removable glass. The glass in Electrolux ovens is not attached to a thread, but to a latch. To remove it, insert the blade of a screwdriver or other thin object under it and press lightly. It should snap open and you can remove it. Then unscrew the lamp and replace it.
Electrolux oven lamp
Bosch ovens
The Bosch oven lamp can be changed either in the manner described earlier, by unscrewing the cap, or by partially disassembling the oven. In the latter case, it is better to contact a Bosch service center.
Hansa ovens
For almost all Hansa models, the lamp is changed in the same way as in the general procedure - unscrew the cap, remove it, unscrew the lamp. The lid in the Hansa oven, like most others, has ridges. You can use them to unscrew it. If you don’t have enough strength, you can press a rag to the cap. After turning, the cap is removed in a forward motion.
Which lamp to choose
For most ovens it is necessary to use lamps with an E14 socket. E14 socket is available for incandescent and halogen lamps. If your oven has a different base or its variations, try to find out this from the oven's data sheet. Sometimes a lamp with a smooth base is required.
As for power, ovens use 40W and 25W light bulbs. The difference between 40W and 25W devices is the power consumption and backlight power. These devices also differ in their service life - a 40W oven lamp lasts 2-5 years, while a 25-volt lamp can work almost forever. Usually, a 25W light bulb is enough to operate an oven in the kitchen; if you need to look at something up close, you can open the cabinet and do it. However, if you or your wife are a born pastry chef, making specific dishes that under no circumstances allow you to open the oven, set the lamp to 40W.
How to change a light bulb in an oven
And how many people are needed for this?
It is not necessary to change the light bulb in the oven very often; one lamp in it usually lasts for several years. But if the light bulb still burns out and you need to replace it, you can do it yourself. The main thing is to be careful and follow the necessary sequence of actions so as not to accidentally break the fragile cap on it.
First of all, you need to completely disconnect the oven from the power supply and let it cool down, if it was turned on before. It is important that all elements are at room temperature, so it is better to wait a few hours after using the Asko OT8636S. If it does not cool down enough, it will be more difficult to unscrew the light bulb due to thermal expansion of the materials.
Detailed instructions for your model can be found in the user manual
.
Then you need to carefully remove the cap from the lamp. Depending on the model, it either unscrews or is removed by snapping the latch fastener. There can be two light bulbs, as, for example, in Asko OCS8664S.
After the cap is removed, you can unscrew the light bulb. In some cases, you just need to remove it from the cartridge if it is not screwed in, but simply inserted.
You need to replace the lamp with exactly the same one. It is better to purchase a new one with an existing sample in hand. In the store, do not forget to tell them that you need a light bulb specifically for the oven - they have increased heat resistance. Ordinary lamps, even if they seem visually suitable, cannot be installed!
Installing a new light bulb is done in the reverse order of removing the old one. You first carefully screw or insert the lamp base into the socket, then put the lamp cap in place. Remember - you cannot press hard on the glass if the lamp or cap does not fit into place! This can cause the glass to burst, and you may get cuts and an unpleasant need to remove the fragments from the oven.
After installing the lamp and cap in place, be sure to check the oven. Turn it on and warm up the camera to maximum to make sure the lamp is selected and installed correctly. Checking is mandatory: if you suddenly choose the wrong lamp, it may burst - and it is better that the fragments do not fall on the food.
If after checking everything works fine and the lamp shines properly, you can fully use the oven again!
Source
Why doesn't the oven heat up?
A breakdown of the upper heating element is completely identical to a malfunction of the lower heating element of the oven. ... This reason occurs very often, both in electric and gas ovens. When the switches are faulty, they do not transmit a signal to the heating element, therefore the oven does not heat up.
Interesting materials:
How are disaccharides formed? How are chemical rocks formed? How to crop part of a figure in Photoshop? How to crop a photo in Photoshop keyboard shortcut? How to cut old glass? How to communicate via video with Odnoklassniki? How to arrange your home in Skyrim? How to clean your iPad from junk? How to clean the outside of a kettle? How to clean wood from dust?
How to turn on the light in a Beko oven?
To turn on the electric oven, press the recessed switch and turn it to the desired position. To turn off the device, press the knob and turn it up. To set the desired heating temperature, turn the thermostat knob and adjust the mode you need.
Interesting materials:
Who are the parents of Peresild? Who are Svetlana Shpigel's parents? Who are Timur Rodriguez's parents? Who are the parents of actress Daria Moroz? Who are Glucose's parents? Who are Ivan Urgant's parents? Who are Jasmine's parents? Who is Andrei Mironov’s own daughter? Who is born on February 3? Who runs Rospotrebnadzor?
How to replace an oven lamp
Replacing a lamp in an oven is not as simple a procedure as it seems. When replacing, it is important not to damage the fragile cap and also follow certain requirements. Picking up the pieces of the lamp and cap can be difficult, so it's best to do it right right away. Then the new lamp will work properly and will only need to be replaced after a few years.
