The zipper on the boot unfastens: what to do and how to fix the situation


What to do if the zipper on your boot comes undone

Even a high-quality fastener on expensive shoes can become loose over time, and the more pressure on it, the faster this will happen.

Reference! Shoes must fit not only in the length of the sole, but also in the width of the boot. If the boot is too tight around the calf, the clasp will not last long, and it will be uncomfortable to walk in it. In this case, take the boot to a workshop to stretch it, or try doing it yourself at home using a special spray.

If the boots begin to unfasten on their own, for no apparent reason, it means that the dog has weakened and is not compressing the teeth tightly enough. What can be done:

  • Tighten the pawl;
  • Increase the grip of the runner with the teeth;
  • Secure the lock on the top of the boot;
  • Sew in a new zipper.

Using a screwdriver

This advice is effective if we are dealing with a metal runner. If your zipper has come apart and the slider is hanging on one of its halves, take a flat-tip screwdriver and insert it into the upper groove of the slider - the one that grooves the lock. You perform this action in order to slightly expand the slider flaps. After the required bosom has opened a little, insert the free half of the zipper into it, and secure the result with pliers.

Do not press the slider too hard with pliers, even if it is made of metal, it may still break.

After all the manipulations, check the slider in action, it should work like new.

Ways to fix the lock and zipper if the boot comes unfastened

Over time, the slider becomes loose or wears out from the inside. To make it squeeze the teeth more tightly, you need to tighten it tighter. To do this, take pliers and lightly squeeze it along the edges on the left and right - there is no need to press in the center. Try it with the clasp open and then with it closed.

If this does not help, lightly tap the same areas with a hammer.

Check how the slider now moves: if it moves tighter, then you are doing everything correctly. Repeat again in different directions to press the lock evenly.

Don’t overdo it: it’s better to repeat the operation several times, gradually increasing the load, than to break the dog in half the first time.

Is it possible to rearrange the slider?

In principle, it is possible, but this applies to things where it is not fundamentally important which way the lock opens (handbags, cosmetic bags, etc.). Repairing the “snake” in this case is extremely simple. Move the runner to the opposite side and sew the loose ends together to prevent the runner from slipping.

If the “dog” is completely broken, do not waste time fixing it and buy a new one at a sewing store. If you are unable to select the exact product, do the following:

  1. Unbend the limiter.
  2. Insert a slider.
  3. Rub the teeth of the lock with paraffin or stearin candle.

All! You can use the lock.

Helpful tips if the zipper comes undone

If the slider still won't hold despite your efforts, try rubbing the teeth themselves with something that will increase grip. Rosin is well suited for this - musicians and dancers use it to prevent the surface from slipping. Lubricate the zipper with an alcoholic infusion of rosin inside and out and let it dry for a couple of hours in an unzipped state - now the pawl will not slip down so easily.

When all else fails, the lock can be fixed in the desired position by hooking it on top with a tongue on something. Sew a clothes hook to the fabric edge of the zipper and hang the slider on it.

As a last resort, you can try replacing the zipper at home with a new one. To do this, you will need, in fact, a new zipper, a spool of shoe nylon or strong thread, a thick needle, and it is advisable to also take a thimble and pliers to make your work easier:

  • Carefully unscrew the old zipper;
  • Cut the new one to the required length, shorten it from the bottom to the iron staples;
  • Place the zipper on the boot and secure it with pins;
  • Sew by sticking thread into existing holes, helping yourself with pliers.

Well, now your boot is in perfect order, and nothing should interfere with your walk.

Scissors to the rescue

If the previous tip didn't help you, you have a few more zipper repair options in your arsenal. So in this case we use scissors. Let's say your zipper has come apart and the slider is hanging on one of its halves. Then we take the second half of the lock in our hands, find the lowest position of the slider, and use sharp scissors to make a small horizontal cut between the teeth. Then we put the slider on the half of the zipper that has the notch in the place of the notch itself, and stretch it to the end. If the part of the zipper under the slider diverges while it is in the top position, pull the slider down (to the place of the cut), and coat the area with the cut with glue.

Please note that once sealed, you will not be able to unzip below this point.

Why lightning may diverge and how to fix it

The main task of repair is not only to bring the zipper into working order, but also to prevent the problem from occurring again. To do this, it is necessary to take into account the causes of the breakdown.

Lightning diverges due to:

  • loss of the internal part of the “runner”;
  • the inability of the “runner” to hold 2 parts of the zipper;
  • Low quality;
  • physical impact;
  • thread or fabric getting stuck in the runner;
  • accumulation of dirt between the links;
  • broken or deformed teeth.

Prevention

To avoid problems with zippers on shoes in the future, you must use the following recommendations:

  1. Clean the fastener links periodically. Treatment with wax or paraffin is required.
  2. Use an old toothbrush to periodically clean the lock.
  3. To prevent the lock from coming apart, it is secured with a thick thread.

To prevent the fastener from coming apart, you should carefully choose your shoes. It's best to try on a pair before purchasing. It is important that it is comfortable and fits properly.

Boot zippers come apart for a variety of reasons. In many cases, the defect is easy to fix yourself. And if this cannot be done, it is better to take the shoes to a specialist.

Gromova Anna, professional in the shoe business. Owner of a small store and shoe restoration and repair workshop.

The zipper on the boot comes unzipped - what to do?

Share on social media networks:

The zipper is a very convenient fastener. It is very often used in the manufacture of clothing, and especially shoes. In fact, it is very convenient, but sometimes you will encounter a problem when the zipper on the boot comes undone. We will tell you what to do in this article.

How to make a zipper on a boot? There are cases in which you don't even have to resort to any method. It often happens when something gets stuck in the snake. Carefully examine the teeth - maybe there is simply a thread stuck between them, which is preventing the dog from moving.

“Slippery” method

The zipper on my jacket is stuck - what should I do? If the snake sticks when you try to fasten it, it means it is not suitable for this type of fabric. If this is possible, simply replace it.

If not, use the “slippery method”. For this:

  1. Lather the clasp.
  2. After this, you will notice that the dog begins to walk much softer.

Important! This is a tried and tested method that was used by our grandparents. In fact, there is nothing simpler, because a piece of soap is available in every home.

You can also use this method, if the zipper on the shoe is fastened tightly, soap it and the dog will walk easier!

The zipper on the boot is stuck - what to do? The next option is using paraffin.

It happens that the slider starts to “slow down” at the most inopportune moment, when you are rushing to work, for example.

The main thing is that the snake itself is made without flaws, and an ordinary paraffin candle will help you deal with a non-working dog. Just run it over the teeth a couple of times, and the result will be visible.

This method is also a great help if you are wondering what to do if the lock on your jacket is stuck.

Important! Before lubricating with paraffin, do not forget to clean the zipper if there is dirt on it. Otherwise, you will simply mix paraffin with dirt.

Rules of care

These simple rules will help preserve the zipper for a long time, and questions about how to repair a zipper on a jacket will not arise:

  • If grains of sand get between the teeth, take the time to clean the lock with an old toothbrush.
  • If the zipper is plastic, be careful when ironing so that the iron does not get on it. In this case, the hot iron may deform the teeth.
  • To keep the fastener longer, follow proper washing procedures. Wash the product inside out, with the zipper fastened.

Oh, how the zipper on a jacket or bag usually jams at the wrong time. You are late for work or in a hurry to a meeting, but she is neither here nor there, no matter how much you crack. In this article we will tell you how to quickly deal with this problem and, most importantly, how to prevent it.

Historical reference

The zipper was first patented in 1893!

With active use, the zipper naturally wears out. It starts to fasten tightly, and sometimes even jams. But you have the power to prevent that wonderful moment when you find yourself captive of your own jacket or when you cannot get your keys out of your bag.

Prevention

If the zipper is not iron, then be careful when ironing so as not to damage the teeth.

When storing, make sure that the zipper does not bend. Fold carefully.

When fastening the zipper, do not pinch the slider with your fingers to avoid accidentally damaging it.

Never pull the lock with all your might, no matter how late you are.

When you fasten the zipper, make sure that there are no stretched areas. It should fasten freely and easily.

The “tongue” is broken

Is the tongue broken or completely lost? This can be easily and creatively solved using a ring from a keychain or a paper clip. Attach it to the slider and, voila, you can use the zipper again.

The runner flew off the zipper

It happens that the slider starts to fly off the zipper. To solve this problem, thicken the zipper stops by placing several turns of thread in their place. Take threads of the same color as the zipper.

The zipper is tight

To ensure that the zipper always closes like clockwork, try never to pull it with all your might, no matter how late you are. But if, nevertheless, it begins to fasten tightly, then this problem can be solved easily and creatively - just rub the teeth of the zipper with a piece of soap, a regular wax candle or rosin. Thanks to these actions, the zippered dog will walk much easier.

Lightning stuck

Most often, metal zippers jam due to the peculiarities of their structure. But don’t rush to give up on them and mentally prepare to take the thing to the workshop. Perhaps there was simply a lining or some thread near the fastener. Gently remove it or carefully pull out the pad by locking the slider or moving it up and down.

If the problem is not in the lining, then most likely some of the teeth on the metal zipper are out of order. To return them to their place, lightly tap the problematic teeth with a hammer. Slightly is the key word. Don't hit the lightning with all your might.

Lightning disperses

Another problem that often happens with lightning is that it begins to disperse.

This usually happens because the zipper slider is loose. This problem can be easily solved with pliers. Just lightly pinch the slider on each edge and that’s it – the zipper will begin to close. You need to clamp strictly along the edges, and not in the middle. And you absolutely cannot do this too much, since the slider will not be able to move at all after your efforts.

That's all for today. As you can see, all problems with lightning are not such problems. But, of course, it is better to prevent them from occurring. We hope you succeed!

Instructions

Contact a shoe repair shop. The technician will competently and quickly replace a part or the zipper

. In this case, there will be no traces left, everything will be very beautiful and neat.

Repair the zipper

V . Perhaps part of the slider has partially broken - this is the movable part of the structure that fastens the lock. If the tongue on the slider breaks and it becomes difficult to fasten it, replace it with a paperclip that matches the color of the shoe. It can also be removed when you need to put on your shoes. Or you can leave it hanging permanently.

Replace the slider if it is cracked or falling apart. Look at the number on the back of it and pick up the same one at a sewing accessories store. Remove the limiter. Bend it using metal wire cutters. Try not to break it, as it will be useful in the future. Put the new part in place of the old one. Put on the removed limiter and carefully tighten it.

Repair the slider if there is no external damage, but the zipper comes apart. In this case, the limiting slides that clamp the zipper

. Using pliers, squeeze the slider slightly at the edges where the zipper links meet. If it fails or there is no result, remove the slider. To do this, straighten the limiter. And squeeze the runner runners, but don't overdo it. If you squeeze too hard, you won't be able to get it back. Put it on again and check how it functions. Don't forget to put the limiter back on. If it doesn't work, replace the slider.

Change the zipper

in the case where several links are missing. But you need to do this in shoes carefully. Carefully open the seams, select the desired fastener and sew it in its original place. Shoes will require special threads and needles. It is better to sew it on a typewriter. There is a special foot for sewing in zippers. The seam must be perfectly straight so that there are no bends or creases.

Sources:

  • insert a zipper into the boot

Runner

is part of the complex design of a modern fastener. The zipper has quietly become an indispensable companion for a modern person, because it allows you to quickly get dressed and better protects you from the cold, unlike its counterparts. In the event of a malfunction, only a person with certain skills and a sewing machine can replace it completely. But don’t rush to do this; in some cases, the issue of labor-intensive replacement of an entire zipper can be solved by easily replacing the slider.

You will need

  • A suitable size slider and pliers. You may need sewing thread, a needle and scissors.

Instructions

It makes sense to consider replacing the slider if your lock is large. If your lock is secret, or small and thin, sewn in to fasten a skirt, you won’t be able to change it. In this case, take the lock to, the cost of replacing it will not be high. If you are sure that a faulty lock itself is unusable, change it immediately. You can try changing the slider, and if that doesn’t help, then change the lock. The cost of changing the slider is low (especially if you do it yourself), but changing the lock with quality and technology is an expensive procedure. It depends on the price of the lock, its length, and also on the technology. So, decide on your tactics.

Do not throw away a damaged runner. It shows the number by which you will select a new one. Remove it from the lock. To do this, you don’t need to “unscrew” the lock - you need it intact. Fully lock so that the slider remains on one of its sides.

If the lock has iron teeth, you need to use available tools to carefully bend the upper lock stop on the side where the slider remains. Remember, after carrying out all the procedures, the limiter will need to be put back. If the lock is plastic, the limiter will have to be removed permanently. This must be done in such a way as not to damage the lock and the lock fabric.

Remove the slider. Without a stopper it will easily slide off.

Take the slider to the hardware department and ask for one like it. If your lock is standard, and the number (size) is indicated on the slider, then there will be no problems. If difficulties arise, all is not lost. Go through other departments with accessories, taking the slider with you, and then you will have more chances to find the right slider.

When you have the slider in one hand and the slider in the other, insert the new slider in the same way you removed the old one. Try fastening the lock. If everything fits together and the lock is fastened, there is one last step left. Reinstall the fastener and tighten it. If it is no longer possible to install it (a plastic lock, or an iron one, but it is broken), secure this side of the lock with threads. To do this, select matching threads and make 3-5 invisible stitches.

Helpful advice

If the thread fastener cannot be installed for aesthetic reasons, you will have to rip the seams on both sides and hide the ends of the lock there (it should be symmetrical). You can do this in a studio or try it yourself.

If the ends of the lock are hidden in the stitching seams, and there is no limiter, you can remove 1-2 teeth of the lock instead.

Sources:

  • how to change the lock yourself

A zipper is a small detail of clothing. But its breakdown completely disables jackets, bags and shoes. Do not rush to throw away an item if a broken lock is the only defect. Fix the zipper

and continue to use your wardrobe.

You will need

  • - pliers;
  • - awl;
  • — new zipper slider;
  • - lace;
  • - wire;
  • - new lightning.

Instructions

Problems can be of different types. The most common problem is its discrepancy. However, there may be no visible damage to the zipper itself. So the problem is . Take pliers and an awl (you can use nail scissors instead). Bend the metal stopper at the base of the zipper and remove the slider. Gently squeeze the runners with pliers. If you do it too hard, you will be unlikely to widen the gap without breaking the part. Return the slider to its place. Try it like lightning now. If everything is in order, put the bracket back in place and tighten it. If the design of the item allows, squeeze the slider without removing it from the zipper.

If the slider is cracked, remove it in the same way. Pay attention to the number that is stamped on its back surface. Buy a new slider at a sewing store, according to the available number, and insert it into the zipper. If during these manipulations you damage the bracket or the base of the zipper begins to crumble on its own, proceed as follows. Pour clear superglue into this area. When it hardens, it will become a limiter for the slider, and the threads will stop coming out of the fabric base of the zipper.

If teeth have fallen out in the zipper, it is better to have the item professionally repaired. Of course, you can insert the teeth at home, but this is a very difficult and painstaking job. Repairs will cost you quite little, but you will save a lot of time. It’s even easier in such a situation to simply sew in a new zipper. To do this, you first need to remove the old lock. Cut it carefully without damaging the fabric. Buy a new zipper in the right color and size. Fold the edges of the fabric and sew the lock by hand or stitch it on a sewing machine.

Video on the topic

Sources:

  • zipper won't fasten

Each of us is familiar with the situation when the zipper on clothes or shoes treacherously stops functioning normally. Despite this, you can repair the fastener yourself using improvised means and without contacting a specialist.

It happens that a zipper comes apart at the most inopportune moment. You can, of course, be prompt and quickly take the item for repair so that the lock can be repaired by a locksmith. But if there is no such possibility, then what to do then? How to fix the lock and deal with the problem on your own?

Tips and tricks:

  • If you want to increase the service life of the zipper, then impregnate its fabric part with BF-6 glue. If you need to bring a worn fastener back to life, this method is also perfect.
  • Need to trim the zipper a little, but you don't know what to do when the slider comes off? You can use a regular pin as a limiter.
  • In order to prevent unfastening on winter shoes, you need to cut off the hook from the clothing and sew it to the side of the tongue.
  • Do not rush to throw away the metal zipper if it starts to come off a little. It can be easily sewn on using a sewing machine.
  • As for a fabric-based zipper, the loose teeth can be easily sewn on by hand using a regular needle and thread.
  • For products made of thin materials, you can sew a thin zipper, but if the item is made of dense or even coarse materials, then the zipper must be appropriate.
  • Be careful when ironing items that have a plastic zipper, as too high temperatures may melt the teeth.

Why do they lubricate?

There are ways to make the dog move easier. The movement of any fastening elements that cause friction (for example, door hinge parts) becomes softer or smoother if there is a layer of lubricant between the rubbing parts. The zipper consists of two strips, each of which has teeth that fit into each other. The latter can be made of plastic or metal. The links are connected and separated by the movement of a special slider (pawl fastener). The design of the teeth and the way they are connected may vary. The lubricant is selected taking into account the type of zipper.

Types: metal, tractor, twisted (“twist”)

How to defeat stuck lightning

So the zipper is stuck and won't go down, and you're trapped by your item because you have to unzip it to get it off.

Take a regular pencil with a graphite tip and rub it over the teeth of the zipper. This should help. If not, you need to increase the glide, such as rubbing the teeth with soap, lip balm or detergent that reduces friction.

Using a Q-tip, apply lubricant to the zipper and teeth. Then pull the fastener down and repeat the lubrication procedure again. Continue until the clasp is completely undone.

How to lubricate a metal zipper to make it easier to close?

When lightning begins to jam and does not move smoothly, products that are available in almost every home come to the rescue.

To prevent lightning from getting stuck, several proven methods are recommended:

Salo

The first thing that can help perfectly is lard. It is suitable for cases when the clasp gets stuck on shoes or a leather bag. It is better not to use it on textiles.

Camphor

It is also good to apply camphor to the cloves. Apply the product very carefully, with a stick or brush, and it is important that the camphor gets on the cloves and not on areas outside the fastener.

Pencil

An ordinary pencil will also work, thanks to which the zipper will slide along the teeth much easier. You need to choose a product with a soft stylus, and rub the teeth of the fastener when the zipper is closed.

Paraffin candle

Another available remedy is a paraffin candle. With its help, you can lubricate the teeth and then the plastic fastener will start working again, like new. But, there is one important nuance. Very often, the fastener begins to jam because, during washing, either the remains of washing powder have accumulated between the teeth, or dirt and debris have simply accumulated. In this case, it is recommended to first take a brush and carefully clean the space between the links.

Soap

Soap is ideal for dealing with the difficulty of fastening plastic fittings.

In this case, the soap must be dry and it is very important to rub both the lock itself and the teeth with it, then it will move much faster.

Teeth do not close or are moving apart

This is one of the most common and annoying problems. First, try repeating the trick with a pencil and soap, maybe this will improve the glide and allow the teeth to close properly.

If this does not help, then something is preventing the slider from working properly. Look to see if there is any thread or fabric stuck in the lock, carefully inspect all the teeth, maybe one of them is bent. In this case, you need to straighten it with pliers, and the zipper will close normally.

If nothing has gotten into the fastener and all the teeth are straight, the problem may be with the slider itself. Over time, the sliders become loose and no longer hold the teeth together. Take the pliers and squeeze the slider until it catches the teeth again.

If you have damaged a few teeth on your zipper to begin with, you can simply stitch it over the damage if you can get the zipper down enough.

We use pliers

Following this advice, place the damaged zipper on a flat surface and straighten its sides. Place one end of the fastener into the slider as firmly as possible and tighten them using pliers. This must be done in such a way that the inside of the tool touches the outside of the slider. After that, check it out: try moving the slider up and down, this will help you determine whether the sides of the zipper are connected. If everything zips up, congratulations: the zipper is repaired, and you can show off your favorite item.

If the lock does come apart, do not despair, feel free to pick up the pliers, place the slider in them so that its outer and inner halves are inside the tool and pull the pliers and the slider a few centimeters. After this, the side of the zipper that slipped will snap back into place.

The clasp does not lock

When the zipper slider doesn't lock onto your jeans, you can end up in a very awkward situation. If you need to go out urgently and have nothing else to wear, you can do this: thread a key ring into the slider, put it on a button, and then fasten the loop. You can use an elastic band for the same thing.

If the zipper periodically comes apart and pressing the slider does not help, you need to replace it. First, use wire cutters to remove the old zipper and metal zipper stops. Then put a new slider on the zipper and use pliers to secure the stoppers.

Trousers

It happens that the zipper on the trousers comes apart. This usually happens at the most inopportune moment, when you are at an important meeting at work or on a meeting with a girl.

That is why this problem needs to be solved immediately. Having shown cunning and ingenuity, you will understand that even such an incident can be resolved quite simply:

  • You will need a regular paperclip or a keychain ring.
  • Just put it on the button and fasten it with the fastener every time you button your pants.
Rating
( 1 rating, average 5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]