How to clean the powder tray in a washing machine

Most housewives believe that it is not necessary to clean the washing machine tray intended for powder. They believe that it cleans itself from the effects of detergents, and their residues are washed out with water. But this is not true, since this unit is a very dirty place in the machine. Over time, deposits from detergents settle in it and mold appears. Because of this, the laundry may not be washed completely and may smell unpleasant. Sometimes the container becomes so clogged that water cannot penetrate through the clog to the detergent. In this case, the functionality of the household appliance is impaired. Therefore, the question of how to clean the powder compartment is not idle.

Does the container need to be cleaned?

Careful operation and proper maintenance are important for any equipment. Automatic cars are no exception. Only if you follow the manufacturer's recommendations and regular cleaning will the device last a long time.

The powder tray is not the most important part of the device. There is no need to clean the dispenser. Many users think so. They are confident that the strong water pressure when starting the program effectively washes out the detergents. This is wrong. Almost always, residues settle on the walls of the container. There are two reasons for this:

• Low-quality powder (the worse the detergent, the more of it will remain on the walls).
• Weak water pressure in the riser greatly increases the likelihood of poor rinsing of the product from the container.

Ditch bleaches and conditioners are truly evil. Such chemistry settles on the sides of the tray in the form of a sticky and slippery film, which hardens over time.

This causes blockages. They can lead to equipment breakdown and failure.

If a serious breakdown occurs and the repairman says that the reason for this is contamination of the detergent container, it will be very insulting and annoying.

It is important to figure out how to properly clean the powder compartment and how to wash the cuvette?

Why is it necessary to clean the powder compartment?

Cleaning the powder reservoir is a necessary procedure. It is a mistake to believe that during the washing period, detergent compounds are washed out of the compartment with water and do not accumulate inside it. In fact, some of these substances settle in the washing machine and require cleaning measures, since the resulting lime deposits and residues of household chemicals interfere with the water supply during automatic washing due to the closure of a special hole. As a result, the powder does not get inside the machine and does not participate in the wash, so it is ineffective. Often such carelessness on the part of the housewife leads to the breakdown of household appliances.

Dirt and mold deposits in the powder receptacle will inevitably end up in the laundry drum. Things will be dirty, and in the best case they will have to be rewashed, in the worst case the clothes will be ruined.

How to clean the dispenser mechanically

The MCA cuvette is the dirty part of the device. The only dirtier things are the tank, hoses and pipes. It is very difficult to get them out and wash them properly. Cleaning the container is not difficult. He is always in sight.

Often the machine stops working normally when powder is clogged in the container. You invite a specialist to your home to carry out repairs. He doesn't fix anything. Simply wash the dispenser and the device functions again without any problems. The specialist leaves and charges a lot of money for the visit and a basic procedure. It's a shame? Undoubtedly! You could read on the Internet how to remove the powder and deal with the problem yourself.

To avoid troubles, make it a rule to clean the compartment every 2-3 washes. Some users do not know how to remove the container. It couldn't be easier to do this. Most machines from different manufacturers are equipped with a simple straight dispenser with a locking tongue. Press down and slightly pull the device towards you. The cuvette will come out quickly and easily.

There are very few SMAs with non-standard trays. They are all well known. These are Indesit and Ariston.

Some models of vertical machines have a compartment built into the body. Taking the tray out of them for the first time is not easy, but it is possible. The main thing is to get used to it and understand the principle by studying the video instructions in detail on the Internet.

The easiest way to remove unnecessary contaminants from a container is mechanically. You need to do this:

• Remove the container and rinse thoroughly with hot water.
• Simply rub it with a hard sponge or brush. This way you can remove particles of dried detergent and sticky residue.
• Rinse the container thoroughly under the tap and wipe dry.

This method without soaking and using chemicals is suitable if the cuvette is not very dirty.

There is no need to use overly hard brushes. There are special marks on the surface of the dispensers that are easily erased when exposed to particularly hard surfaces.

Tips to avoid the problem

It turns out that cleaning the washing powder tray is not particularly difficult. However, following some helpful tips will help speed up the process and save you from unnecessary headaches.

Therefore, consider the following points:

• after finishing the machine, the powder loading hole should be left slightly open, which will prevent the appearance of unpleasant odors;
• so as not to wait for final drying, wipe all parts of the tray dry;
• install a special filter for water purification in front of the inlet hose, which will prevent clogging of the unit with impurities from the water supply system;
• follow the dosage of washing ingredients to completely wash them out;
• If possible, replace or reduce the frequency of use of powdered products, choosing an alternative to liquid products.

To achieve the most perfect result, you can use combined tray processing methods. The materials used in the video below include Amway ZOOM concentrated cleaner, diluted vinegar essence, an old toothbrush, a melanin sponge, a regular old sponge, and Bioline cleaner.

Careful handling of household appliances guarantees long service life and makes it possible to comfortably use additional functions. Therefore, you should not forget about maintaining cleanliness in the loading hole, for which you carry out preventive cleaning, use chemicals, or use homemade analogues.

How to clean powder from a washing machine: chemicals to help

We figured out how to wash powder in a tray with light dirt. It may happen that mechanical cleaning was unsuccessful. Contaminants in the form of old detergent, plaque, and mucus remain in the compartment.

What to do in this case? How to dissolve hardened laundry detergent and stubborn dirt? There is only one way out - use the right chemistry. With its help, you can tidy up the dispenser, as well as the insides of the washing machine. Great, because other parts also need cleaning.

Follow the instructions:

• Open the detergent compartment and add the amount of chemical recommended by the manufacturer. Do not exceed the norm so that the parts do not break.
• Remove things from the drum and turn the SMA to “idle” at a maximum temperature of 90–95 degrees.
• Restart the rinse cycle.

Cleaning the tray and machine is finished!

This method has its drawbacks. The main one is that it does not allow you to remove old dirt and completely clean a very dirty compartment.

Prevention measures

Preventing dirt from appearing in the SMA tray is easier than fighting it. Regular care is important for this.

Follow these simple tips:

• Rinse the container with clean water and wipe it dry after each wash.
• After washing, do not close the compartment. Leave it open until completely dry. In a humid environment, bacteria multiply quickly. In dry conditions - no.
• Every 10 washes, perform high-quality cleaning using chemicals and brushes.

Now you know how and with what to clean the detergent dispenser in an automatic washing machine. With our recommendations, it will be easy to achieve a sparkling clean tray. The main thing in this matter is regularity. Then there will be no problems and the machine will serve without breakdowns for many years.

Source

Combined cleaning

Is water not getting into the compartment? The cuvette is completely clogged. Cleaning with chemicals will not work. Mixed cleaning will help. It goes like this:

• Pull out the device and soak it in a basin in water for 5 minutes (water temperature - at least 60 degrees).
• Add or pour chemical into the water and mix well.
• Let the dispenser sit in the solution for several hours.
• Remove the container and scrub vigorously with a brush.
• Rinse, dry and reinstall.

What to clean: the best products

We have decided how to combat pollution. Now let’s find out what is the best way to wash fossilized washing powder. Use factory-made household chemicals. It will bring the cuvette and the main components of the unit into proper shape.

The most popular means:

• Frisch Activ. An effective remedy in the fight to keep the dispenser clean. Suitable for trays with light soiling.

• "Doctor TEN." Recommended for dry cleaning of the washing machine and dispenser. Also used for minor stains.

• Sandokkaebi. The most effective composition of South Korean production. It cleans not only the container, but also the hoses and pipes of the SMA. An important advantage is the affordable price.

For soaking the tray, you can use more aggressive chemicals, because it is not poured into the machine. Suitable products for cleaning plumbing fixtures and toilets. For example, “Domestos” or “Toilet duckling”.

Household chemicals

The compositions, which are sold in all hardware stores, can easily cope with contamination of the powder tray. The most accessible and effective are:

• White;
• comet;
• Cif cream;
• Cillit Bang;
• Domestos;
• Toilet duck.

If there are lime deposits, heavy dirt and a musty smell, special products will help, the use of which does not require removing the tray and its elements. Compositions such as Sandokkaebi, Bork K8P, Frisch-aktiv, DOCTOR TEN are capable of removing dirt and mold deposits, as well as powder residues. The procedure is carried out in several steps:

1. measure the required amount of product according to the instructions;
2. place the composition in the powder receptacle;
3. run a single wash at a temperature of 95 ° C;
4. start the rinse mode at the end of the wash.

If the manipulations did not help, and dirt remains in the tray, you should resort to other means. In this case, you will need to remove the container.

Natural remedies

Don't like chemistry? Use natural remedies to combat dirt and plaque in the litter box.

• Soda. Add the same amount of soda to half a glass of water. Stir with a spoon. Pull out the cuvette and pour the resulting composition into it. Rub thoroughly with a sponge. Wash with water.

• Soda and vinegar. Remove the container. Pour baking soda into it and pour vinegar on top. The two main ingredients will cause a reaction (be careful not to burn yourself). After this, vigorously scrub the walls of the container with a brush. Was the effect weak? Repeat the procedure.

• Lemon acid. It will help to clean not only the cuvette, but also the pipes from powder, scale and dirt. Pour 2-3 tablespoons of acid into the powder compartment and run a “idle” wash at 60 degrees. A pleasant bonus of this cleaning method is the light lemon aroma after washing.

• Vinegar. Dissolve 1 liter of hot water and 250 ml of 9% vinegar in a basin. Place a container in it. Leave to soak overnight. In the morning, remove dirt and scale with a sponge.

Pollution prevention

To ensure that the container and other compartments of the machine remain clean, the equipment must be properly cared for:

1. Use good detergents. Low-quality gels and powders, as a rule, do not completely dissolve in water, which leads to troubles and even breakdowns.
2. Clean the powder and conditioner compartment regularly.
3. After each wash, remove the detergent compartment from the machine to allow it to dry.
4. Install a water softener. It will help extend the life of the detergent container. Less contamination will form on the walls of the dispenser.

If the plaque inside the tray has hardened to such an extent that it cannot be removed, the only way out is to install a new dispenser. However, if you regularly clean it of scale and plaque formations, such problems will not arise.

Source