What to do if the silicone case. How to stretch or shrink a silicone phone case

How to stretch a silicone phone case

Silicone is a fairly durable material, which at the same time is very elastic. The latter property is associated with a significant disadvantage of such covers - they stretch over time. Well, if you want to speed up the process and increase the size of the overlay immediately, there are several effective ways:

• The simplest option, which does not require the use of tools and devices, is manual pulling. The cover should be wrinkled well, twisted, folded and other movements that can increase the size.

The second method involves moderate heating to achieve greater plasticity. Warming up can be done with a household hairdryer, and then try to put the cover on the smartphone. It is important not to exceed the temperature so as not to melt the material (important when using a hair dryer). The latter method will require knowledge of how to soften silicone. You can achieve your goal by immersing the cover in hot water. Next, the overlay is placed on a pre-prepared wooden model, the dimensions of which correspond to the desired stretching result. After putting on the cover, it is warmed up again in water for 60 minutes and cooled at room temperature. Now you can remove the cover from the block, wipe it dry with a rag and try to try it on your phone.

The presented methods will help to cope with the problem of a small case if its size needs to be increased by 1-3 mm.

Paper

All you need is a sheet of paper, a glue stick and scissors. Initially, you need to make markings according to the size of the phone. Then cut out the desired stencil from paper. Please note that on one side an allowance must be allowed. This is done so that when gluing the seam is on the outside. Next, simply fold the cut out stencil in half, glue the seam, wait until it dries, and you can use it. Such smartphone cases are only suitable if you urgently need to provide minimal protection for your smartphone. In fact, a paper case will not protect your smartphone from various influences.

How to stretch a leather case

A leather case that does not fit on the phone or fits too tightly, causing the buttons to operate, it is advisable to enlarge it a little. The leather stretches well if it is wetted with water, and when dried it retains its given shape, so use a simple method.

• Try to select or cut a piece of wood that is the same size as the mobile.
• Split the resulting workpiece in half along the flat side. Insert a thin plastic plate into the slot.
• Wet the cover well in warm water and stretch it onto a wooden model.
• Leave it to air dry without heat, otherwise the leather will dry out and crack.
• After about a day, when the cover is dry, remove the plate, and then the wooden block.

The accessory will stretch to the desired size. If you use a mixture of alcohol and glycerin instead of water, the drying time will be reduced, the procedure will be more gentle on the skin, and the surface will retain its shine.

Why do you make your own covers?

The answer to this question will contain three factors at once, each of which is important for a certain circle of gadget users. The first factor is the high cost of truly original branded products. Accessories for new phone models have an increasing number of properties, but their manufacture, or rather, their transformation from an ordinary transparent bumper is accessible to anyone.

The second factor is the desire to make a phone case with your own hands of a certain color, shape and with specific characteristics. If you cannot find products even in the collections of leading brands, show a little imagination, use numerous techniques and tips from our article to create a case that will fully satisfy your wishes and requirements.

The last, third factor is frequent changes of image. Here both factors will be combined - it is expensive to buy covers for each image, and it will be extremely difficult to choose one for many specific looks. Thanks to our recommendations and detailed instructions, you can create a case for any style, ideally complementing your look with an original accessory.

How to solve the problem of enlarging the case

As for tips on how to stretch a leatherette phone case, slightly different approaches are used here.
We all know that skin tends to stretch. Good leatherette also provides similar opportunities. By analogy with natural material, you can try to stretch the case by inserting a model of your device into it, for example, made of wood. First, the base must be split in half, installing a spacer in the center, which will increase the capacity of the case. Experts advise placing this entire structure in warm water and leaving it for a while. After the spacer is removed and the case is dry, it should acquire a new desired shape that will allow it to be easily installed on the gadget.

Do not forget that before trying this method, you should, again, contact the seller and tell him your complaints regarding the defects of the ordered product.

Summarizing all of the above, we want to say that it is still possible to return the shape of a deformed phone case. But not everyone. Therefore, before purchasing protection for your device, make sure that it is perfectly compatible with your device by requesting information from the seller. Then, if the slightest discrepancy arises, you will have a reason to return the case, and not look for ways to change its size. Have a nice case!

It is not difficult to stretch a leather case

Beads

Beads presuppose the presence of a case and the open question “how to paint a smartphone case.” To decorate it with beads, you need to literally cover it with this material.

You need to apply glue to the old case, and then carefully apply the beads. It is very small and very easy to lose. To create an even pattern, it is recommended to trim the beads with a ruler. With its help, the decoration of your phone will be as smooth as possible.

This work is very painstaking, and it will take a lot of time to decorate the entire phone in this way. Moreover, after the beads are glued, you need to be as careful as possible with the phone. Any careless movement may cause the entire decoration to fall off.

How to make a silicone case smaller

As already mentioned, silicone has a significant drawback - it stretches after some time of use. For this reason, the question arises of what to do if the silicone case is stretched. You can try to reduce it using the method below. The presented method has been tested by many people and is guaranteed to help solve the problem.

Before taking specific actions, you should know that the size will decrease by 1-2 mm. If the cover is very loose, then it is better to buy a new one and not waste your time. In case of a minor sprain, the following steps must be taken:

• Choose a pan that will allow you to completely fit the lining without touching the edges. Pour water into it and put it on the stove to heat.
• Bring water to a boil and place the accessory in it.
• Cook the lining for about 5-7 minutes, holding it with a fork so that the water completely covers the material.
• Remove from the pan and leave to cool completely.
• Wipe dry and try on the phone - the case has shrunk and fits tightly to the body.

Before performing the procedure, it is important to pay attention to the material of the lining. The polymer alloy, if transparent, will become cloudy, but real silicone will not change its properties. However, for opaque accessories this does not matter. Some users note that they were able to partially restore transparency by placing the case on the battery for a while.

Vitaly Solodky

Accessory with liquid inside

Making a water cover with glitter inside is very easy.

1. You need to prepare: a transparent silicone case; glitter and confetti; waterproof glue; oil (sesame, refined vegetable, flaxseed).
2. Carefully make a slit in the silicone and pour confetti and glitter inside.
3. Add oil.
4. Seal the slot with glue and place a weight on top to secure it.
5. Wait about 30 minutes for it to harden.

Master class on making a water, gradient and edible case:

How to buy a quality case?

Defects in accessories happen in any store, even the most famous ones, but the approach to solving the problem is the hallmark of good stores.

If you are forced to choose a case online and are unable to try it on and hold it in your hands before purchasing, you can always use the cash on delivery service. This service is provided by most delivery companies in Ukraine. And suspicious sellers who refuse to send you goods in this way should immediately arouse your suspicion.

Most likely, they are selling a low-quality product and are afraid that you will refuse it.

It often happens that it is not profitable for you, as a buyer, to pay the cost of delivery, and even the cost of the cash on delivery service, but the online store site meets you and pays for the delivery of any goods at its own expense. You can order a high-quality cover at a very inexpensive price, try it on at a Nova Poshta branch before paying, and at the same time not overpay inadequate amounts.

Floral motifs

If you like floral patterns, you will definitely want to repeat this technique. You can use dried flowers to decorate your smartphone case. You can do this yourself by placing colorful petals between the pages of a book, or buy ready-made materials at an art store.

Arrange the petals beautifully on the case and cover your work with a protective layer of varnish.

Comments

The desire to decorate your phone arises in everyone who enters cellular communication centers at the sight of attractive cases and bumpers. But not all of them can provide the communication device with adequate protection in the event of an impact or fall. And if the range includes a shock-absorbing bumper for your phone, it will either not be suitable for your model, or its cost will be astronomical. There is only one way out - to spend a little time, imagination, effort and make a beautiful case from scrap materials.

Everyone has a desire to decorate their phone.

The colorful bumper can be made from silicone to make molds without touching brushes or glue.

To prepare the material you will need:

• Construction silicone;
• Potato starch as a thickener and to give white color;
• Color or acrylic paint.

It is better to use silicone gloves during the kneading process. This way your hands will feel the material, and you won’t have to wash them for a long time.

Manufacturing technology:

1. After squeezing out the silicone, you need to add two tablespoons of potato starch to it.
2. The process of kneading silicone “dough” is similar to the preparatory stage before modeling from plasticine. It needs to be kneaded until the mass becomes homogeneous.
3. If you divide the resulting mass into several almost equal pieces and add a color to each of them, you will get multi-colored balls. They need to be flattened, folded so that each previous one peeks out from under the previous cake by a few millimeters.
4. Using a rolling pin, roll out the workpiece so that it is enough to cover the back wall of the gadget, its edges and a small bend on the front side.
5. The phone is wrapped in the resulting multi-colored or plain sheet of silicone.
6. It needs to be pressed a little into the “dough” to mark the holes for the camera and speaker grille, located on the back side.
7. Connectors and control buttons on the side elements of the phone must be marked by running your thumb along the entire perimeter of the phone.
8. The silicone should harden. Its readiness time depends on the thickness of the rolled layer and the data provided by the manufacturer.
9. It is better to remove excess silicone immediately using a stack or a plastic knife. Without excess material it is easier to form the corners.

Advice! Hardening of the silicone mass can take up to 12 hours. Move the SIM card to another phone or forward calls. Otherwise, the cover will not have a smooth surface.

Glue threads

Initially, you need to wrap your smartphone in paper. Next, secure the folds and joints so that they do not stick out, and secure them to the screen with tape.

Next, you need to make the base for the back cover of the gadget. For this purpose it is necessary to use glue. Using it, you need to cover the back side with glue, and do the same with the side surfaces. You need to wait until the composition dries and remove the wrapper from the smartphone.

After this, you need to wrap the glue on a ruler, or a similar device taking into account the width of the phone. When it dries completely, it needs to be cut through the opposite edge. So it is necessary to dot the space with peculiar fibers.

Comments

✉ EMAIL: Cooperation/Współpraca/Business Inquiries:

Don't know how to make money? Ask me how and I'll tell you

Well, let's try to adjust the case to size? And here you will find even more descriptions and photos

Don't forget about additional savings with purchases on Aliexpress. My choice of proven cashback - from 7 to 18 percent savings on all products from Aliexpress

An affiliate program that helps promote the channel and earn money

Link to the bumper/case this Well that will try the case to fit? And here you will find more descriptions and photos

Don”t forget about additional savings when shopping on Aliexpress. My choice of validated cashback from 7% to 18% savings on all products from Aliexpress

Affiliate program that helps to promote your channel and earn Source youtube.com/watch?v=KuNZYfaDQc8

Video content was added by the user “ Aleksa Onle

” to your video channel for 3 years. ago, it has already been viewed 155,942 times. The video material was liked by 1,179 and disliked by 1,540 website visitors. What do you think about this video for Android? Write below and let's discuss!

This video material for phones, smartphones, tablets and other digital devices can not only be viewed online on the Android.Net website, but also downloaded completely free of charge and without any registration in files: mp4, webm, 3gpp and even mp3. To download files, you just need to click on the “Download” button at the top of the site and move the slider all the way to the right. Do you want more interesting videos from this author? You have the opportunity to watch other videos for Android

from this user, which are also published in the official video channel of the author https://site/s/Channel+Aleksa+Onle, as well as other similar videos related to Android phones, smartphones, tablets and other electronic devices. Our video site has a modern adaptive design that allows you to view videos on any portable electronic devices and on TVs with the “Smart TV” function.

103583

If you notice an error, select a piece of text and press Ctrl+Enter

Recommendations

When choosing a method for making a case for your phone, first of all you need to be guided by the requirements that the phone case must fulfill.

If you choose a simple, beautiful case, it will not fully protect your phone. After some time it will break or stretch. After that you will have to buy another one of the same kind.

A book case provides the best protection. It protects the phone on both sides, preventing it from cracking or dust or sand getting into the speaker. Moreover, it has a very convenient smartphone location that allows you to watch movies.

Over time, the case stretches and moves around the iPhone 7

But the saddest thing about this accessory is its fragility .

In addition, I have a couple more cases for the iPhone 7, which I change according to my mood and depending on the specific situation - we’ve already talked about one armor-piercing one, and we’ll look at another one a little later.

And due to regular putting on and taking off, the official Apple case has stretched and now does not fit as tightly to the device as it did before. And in the area of ​​the camera, which is partially visible in the photograph, he is generally shaking.

As a result: I highly do not recommend it - a waste of money and nerves.

Post rating:

( 4.13 out of 5, rated: 8)

Return or exchange guarantee

A money-back or exchange guarantee for defective goods can be very useful, most good stores are required by law to adhere to this rule and provide you with such a guarantee for a period of 14 days. However, in the online store Floy.com.ua this guarantee is as much as 25 days! This is an opportunity to test the product in practice, without risking losing your money.

Please note that unscrupulous sellers also write about this guarantee, but they use free ad services and one-page sites to distribute their goods, since you will not be able to check reviews about such a seller or complain anywhere.

When choosing a reliable store, pay attention to the presence of a real address, reviews using authorization through social networks and high-quality advice on the issue that interests you.

Ask if you can come and see the product at the specified address? If the seller refuses to show you the product and insists on sending it with advance payment or partial payment, he is most likely a scammer.

Our online store also has a channel on YouTube, and you can see what the type of case you are interested in looks like.

Not all cases fit the phone equally well. Many users are faced with the problem that the dimensions of the protective accessory do not match the actual dimensions of their device. For some, the gadget falls out of the case, for others, on the contrary, the case turns out to be much smaller than the device. Today RosCase will tell you how to deal with such problems, how to make a silicone phone case smaller or larger.

How to make a phone case from a balloon

The technique for creating such a bumper is similar to vacuum packaging a phone in latex.

1. The balloon is inflated to medium size.
2. It must be laid on a flat surface, holding the neck with two fingers.
3. Place the phone in the middle.
4. The gadget must be slightly pressed down and the air must be released from the ball.
5. A couple of minutes of work, and the phone is dressed in a new bright shirt.
6. All that remains is to cut holes for the camera and connectors, and the thin material will not interfere with the operation of the buttons.

The technique for creating such a bumper is similar to vacuum packaging a phone in latex.

Useful tips

Before you start making a smartphone case with your own hands, you need to consider the following points:

1. Use only safe materials in your work (liquids without toxic vapors and solid materials that do not cause allergies and comply with sanitary and hygienic standards).
2. Do not give children very small, sharp or loose objects.
3. A homemade case should not injure the skin of your hands and face or contain sharp or cutting elements.
4. The case should not block the speakers and phone camera.

Is it possible to make the rubber boot smaller?

During use, the rubber covers stretch. They can be returned to their original size. To do this, they must be immersed in boiling water. They will become more plastic, and when cooled they should return to their original size.

Some bumpers, made of rubber with a large proportion of plastic, are not as flexible as rubber. But they can also be made smaller at home. If immersing the cover in boiling water does not lead to the expected result, you can try boiling it for 5 minutes - the principle of preparing a polyethylene suction cover. He works. Just don’t put a wet bumper on your phone; the moisture needs to be removed from it.

Preparatory actions

When considering how to reduce the size of a silicone phone case, you can use a simple technique. It involves heat treating the bumper. If it is impossible to return the accessory to the store, you should try to reduce its size using regular boiling water.

Various techniques are used to narrow the cover. Some buyers advise using alcohol or acetone, a freezer or a hair dryer. One of the most adequate methods is the one that uses boiling water.

• Aliexpress - the best iPhone cases. How to find and order iPhone cases from Aliexpress?

You will need two pans. They should be larger than the case itself. The first container should contain hot water, and the second should contain cold water. You need to make sure that there are no foreign impurities in the water so that the cover does not change color. It is also worth considering that it is better to carry out such a procedure with an opaque cover. Otherwise it will become dull.

It is better to add a lot of ice to a container of cold water. It is necessary to create a maximum temperature contrast during the processing of the cover.

Gluing parts

It is still advisable to glue the details of the resulting pattern. The denim will become thicker and denser.

Non-woven fabric is an adhesive base. One side of the non-woven fabric is smooth, and the other is rough to the touch. The rough side is droplets of glue. Adhesive material can be purchased at any sewing department.

Glue the pattern pieces.
Photo: eSovetnik.ru Cut the interlining according to the pattern of your cover pattern without seam allowances. That is, only the central parts of the cover pattern need to be glued.

Turn on the iron. Using glue (rough) put the interlining on the inside out of the pattern. Wet it with a spray bottle and iron it with an iron.

A very hot iron will burn the adhesive, so do not heat the iron too much. To prevent the non-woven fabric from burning, it can be glued through gauze or other thin fabric.

Processing the top cut of the pattern

We process the top cut of the pattern.
Photo: eSovetnik.ru Now you need to process the upper sections of the pattern using a regular hem seam.

According to the seam allowance, 1.5 cm was allowed for the width of the seam, so the hem should not be more than one and a half centimeters. If you bend it further, the phone will stick out from the case.

For convenience, you can iron the top edge of the product, so you will not be mistaken with the size of the hem. And it will be much easier to secure the ironed cut with machine stitching.

The hem may be less than one and a half centimeters, but in this case the case will be slightly larger than the phone.

Restoration of shape by thermal method

Most often, this kind of deformation and stretching occurs when the covers are transported carelessly or when stored in improper conditions without a special damper insert. Such cases take an irregular shape and do not fit tightly on the smartphone. However, if such an accessory was made exactly to size, this can be corrected.

To restore the cover, we need two containers of water; it is very important that the size of the containers used is larger than the size of the cover itself. If you place the case in a small container, you risk deforming the accessory even more.

In the first container, you need to bring the water to a boil and leave it on low heat, and in the second, the water should be as cold as possible.

Dip the stretched cover into boiling water and hold for up to 5 minutes (time depends on the thickness of the cover). After the cover has warmed up well enough, transfer it to cold water, and if there are any deformations on the edges of the bumper, straighten them with your hands and in this position lower them into cold water.

Such a sudden change in temperature can cause a slight decrease in size, but if the case has a significant deviation in size, you most likely will not be able to reduce it.