How to unscrew?
If the atomizer tank does not unscrew, you can solve the problem in the following ways:
- Stop the base. There's no point in putting in too much effort. This is fraught with cracks in the glass, which will become unsuitable for further use. The base can be secured with any thin object that fits into the duct opening. This will help secure the body.
- Latex gloves. The easiest way to unscrew an atomizer, glass or drip tip is to use rubber-based gloves or a similar thin mat. This will prevent your fingers from scrolling along the body of the product.
- Electrical tape and plaster. If you cannot manually disconnect the clearomizer, use pliers. In order not to deform the glass, the vape is wrapped with insulating tape in 1-2 layers; this should be done extremely carefully. The pliers squeeze the tank only lightly, otherwise the glass will be scratched, and in the worst case, it will burst.
When the tank unwinds, it is better to postpone refueling. All this is a consequence of active vaping - the electronic cigarette needs service. Using a wet cloth or a thin stream from the tap, the joint surfaces are washed and the threads are cleaned. When there are no oily slurry residues on the fastenings, everything is done correctly. Unscrew the rest and rinse thoroughly. Thanks to this, you can fix the glass with only a few turns: clean parts prevent liquid leakage.
Methods
Methods
Is it possible to wash an electronic cigarette? Can. There is more than one way to clean a device from old fluid. Before implementing each of them, you need to leave it alone for a while.
The cigarette must be cooled down, it cannot be washed while hot, otherwise the vapor generator will fail.
Blowing and flushing
Blowing and flushing
To get started, disassemble the electronic cigarette into parts. Disconnect them from the battery. Then blow around the mouthpiece. Remaining liquid should be removed. After which you can start washing the device.
How to wash? Water acts as a cleaning agent. No liquids need to be used. Rinse all parts of the device with warm water, but not under the tap. It’s better to pour a little into a bowl and change it when it gets dirty.
After which you need to blow it out a second time and lay out all the parts on a clean towel. It is important to eliminate all moisture. Before assembly, be sure to check whether the cigarette has dried well.
Chemical treatment
Chemical treatment
Infrequent cleaning leads to the accumulation of soot on the heating element. In this situation, they are not washed with water, but treated with other solutions, because water will not help get rid of a large amount of combustion products.
How to clean an electronic cigarette:
- Disassemble the devices into components, there may be five or fewer of them, it all depends on the vape manufacturer.
- Pour rubbing alcohol into a separate container.
- Take a cotton swab and wipe down each piece, use separate swabs and change them frequently.
- Then you wash them in warm water and leave them to dry for a day.
Chemical treatment of the device is the most difficult. It is necessary to process each part separately, without missing a single section.
The help of professionals is not needed here; you can do everything yourself. It is only advisable to resort to such processing less often. Therefore, it should be disassembled and washed with plain water more often.
How to use a vape correctly?
Problems with detaching and fixing parts in most cases arise due to violation of the rules of use. Professionals recommend:
- Act carefully and consistently. First, the drip tip is unscrewed, then the tank cap, and only then the glass and atomizer are removed. If everything unfolded chaotically, you shouldn’t be surprised at the problems.
- Protect the electronic cigarette from high temperatures. This may lead to deformation of the glass and case.
- Securely fix the evaporator. It is difficult to screw or unscrew the tank due to the crooked position of the atomizer.
How to replace the evaporator in the tank?
How to change the evaporator?
- Before installing a new evaporator, it is recommended to disassemble the tank and rinse it with ordinary warm water, removing traces of dirt.
- Then you need to screw in a new evaporator, having first dripped it with the liquid with which you will fill the tank.
- Fill the tank with liquid and let it sit for a few minutes.
12 Dec.
2022 Interesting materials:
What are maternity payments and what do they consist of? What is the business reputation of an organization? What are cash equivalents? What is Device ID? What is a 32" diagonal? What is a differentiated payment type? What is Application Manager? What is a display port on a video card? What is a display port? What is DLC on Steam?
Other unscrewing methods
You can unscrew the atomizer from the base or the tank from the evaporator using special substances. During active vaping, a corrosive coating from burning and liquid remains on the inner surface of the electronic device. This leads to boiling of the elements, which are tightly fixed to the thread and are not susceptible to external influences.
VD-40 will help with servicing your vape; the composition is easy to find in any hardware store. Through the holes in the air duct or through the hole for vaping, you should try to drip WD-40 onto the connection and threads of the parts. Then wait 5-10 minutes. During this time, the plaque will dissolve, and the mobility of spare parts will improve.
After cleaning, it is important to rinse the atomizer to remove any residual WD-40.
How does a serviced atomizer work?
The manufacturers of these devices made sure that users, even without skills, could figure everything out on their own.
The serviced atomizer, as it is also called for short OA or OBAT, is one of the most popular models of electronic vaporizers today.
How does a standard atomizer work?
The 510th connector (the most common) from the battery transmits energy to the site. A stand with screws and an air duct are already placed there, the spiral and wick produce heat and evaporate the liquid from the cotton.
The steam is then supplied to the mouthpiece using the user's draft. All contents are enclosed in a collapsible case, implying a complete replacement of all existing spare parts.
Coil means “spiral”. Usually two alloys are used - nichrome or kanthal. Nichrome is made from the elements nickel and chromium, this is usually indicated in the labeling. For example, Cr40Ni60 means the alloy contains 40% chromium and 60% nickel. Heat resistance is high and can reach 1400 degrees Celsius. However, it will be more difficult to wind this type of wire than Kanthal wire.
Kanthal is originally an alloy of iron, chromium and aluminum. It bends well and has shape memory. Therefore, winding will happen quickly and easily, like thread on a reel.
For anyone who has recently become interested in vaping, it is worth choosing BOATs of the “Lemo” and “Tayfun” brands.
Their advantages are that they are simpler in design and are also equipped with replaceable Kanthal wires. It is very comfortable.
Selecting Kanthal for Winding
There are some conventional standards for winding. In a large list of different types of wire, it is better to choose Kanthal marked A1, since it is softer and more pliable, in contrast to the following A2 and A3.
As a handy tool for winding, you can use a very ordinary screwdriver. Its sting radius is sufficient. The best option for coil is 3-5 turns, with a diameter of no more than 0.4 mm.
Thus, the battery power will not be wasted and heating will be uniform and sufficient for an average of 30W.
Atomizer maintenance includes regular washing of the fetyl and burning of the coil. This is a necessity in order to maintain the desired level and performance of the device. This way, the liquid can flow to the heater evenly, and the taste of the steam will always remain clean and pleasant.
If your purchase choice fell on serviced atomizers, it would be right to give preference to the steel Lemo-2 and Serpent Mini RTA. They are more than “tenacious” not only due to the internal filling, but also the outer casing made of high-strength steel. It is very difficult to break these and most likely will not succeed without special physical diligence.
These models feature simple power adjustment and active supply of liquid to the evaporator, which will bring maximum vaping pleasure. Manufacturers often include a mouthpiece, ready-made windings and even complete factory-assembled repair kits in the product package.
Why should you be careful with glass?
Glass is the most vulnerable element of a vape device. Owners of rare electronic devices ordered from AliExpress or other foreign resources can verify this. It is difficult to find components for new devices in stationary vape shops.
Cracked glass cannot be repaired. Moreover, with frequent unscrewing and tightening, the crack will spread.
To avoid spending money on buying a new vape, it is wise to clean your electronic cigarette after every second or third refill.
In order for you to enjoy the vapor from your electronic cigarette, you need to refill it on time and correctly. Otherwise, the steam generator will simply have nothing to produce steam from.
How to refill the tank of an electronic cigarette correctly, and what safety rules exist?
When and why?
When and why?
The need to clean this device is due to the formation of burning on the internal elements. You should not allow burning to enter your body; it will end badly for your health. Pure e-cigarette is safe to use.
In addition, fumes affect the operation of the device. The vape begins to work poorly, and therefore the harm from its use increases.
Burnt residues on parts lead to premature failure of individual parts. The device works for less time, and liquid may also leak into the battery.
How do you know when you need to wash your device? When contaminated, the vape changes the taste and smell of the vapor, making steam generation difficult.
You should also rinse when changing the fluid. This information is useful to know if you like to experiment with e-liquids for refilling your vape.
Frequently asked questions
The refueling process is quite simple, but if certain rules are not followed, various difficulties may arise. For example, what to do if the tank does not unscrew or the following:
So, you are a beginner vaper.
You recently purchased your first vape and don’t know how to refill your e-cigarette correctly. The seller was unable to demonstrate this in the store, and the vaping process can't wait to start. Let's try to answer this question.
Short story
Since that time, such gadgets have changed beyond recognition and have become hundreds of times more powerful.
If previously they existed only to help a person quit smoking more comfortably, now almost every fifth person has such a device. Some, especially young people, have become addicted to vaping liquids of different flavors, so the popularity of electronic cigarettes is increasing exponentially. Many people are interested in how to care for an electronic cigarette. This is a simple procedure that does not take much time. The first ES were disposable . They were relatively inexpensive, and their manufacturers claimed that this kind of device could replace up to 2 packs of cigarettes for a smoker. In fact, due to their low power, they lasted for a very short time, and the amount of steam and taste left much to be desired. Of course, there was no question of any cleaning: after use, the devices were immediately thrown into the trash. The batteries of such devices could not be recharged, and the taste of the liquid could not be changed. They began to be replaced by the first reusable ES.
Such devices were called e-cigarettes. They cost much more than their disposable counterparts, but they were practically the same in terms of the amount of vapor and taste. For such gadgets, cartomizers were used - removable caps filled with liquid with a certain taste and aroma. The cartridges could be refilled, but the process was labor-intensive and fluid often leaked. The battery of such devices could be recharged repeatedly, but it was impossible to hover while charging.
The evaporator was a twisted wire that was inserted into the cartridge and heated it. The charge held very little, and the composite cigarettes themselves quickly failed, so they had few admirers. Soon, eGo and Armango format devices (models ce4 and ce5) entered the market, which had an improved liquid reservoir and an evaporator. Soon they too became outdated, because they were replaced by various box mods, as well as mechanical mods, which are constantly being improved.
Types of tanks
Structurally, tanks are divided into two subtypes.
- With a spiral at the top. If the spiral is located at the top, then you need to unscrew the top part of the tank, then carefully pour the liquid along the walls of the vessel, avoiding getting into the hole in the air duct. The liquid must not be filled to the top, otherwise it will leak out when the top is tightly closed after filling.
- With an evaporator at the bottom of the clearomizer. With this arrangement, you need to unscrew the clearomizer from the battery counterclockwise. Then turn it over and detach the bottom part. Then, carefully, as in the first method, pour in the liquid without touching the air duct. Then, screw in the lower base and battery in sequence.
It must be remembered that if you perform top filling, then immediately after opening the lid, the liquid must be filled as quickly as possible. You also need to ensure that the lid is always closed and liquid does not flow out through the air duct openings.
What is a 510 connector
Many people know what a 510 connector is, but few know how to care for it; in vaping you won’t go far without 510 connectors.
They seem to be on every atomizer, tank and mod that has been produced in the last few years, but what exactly are they? – Although the concept of two things that screw together is very simple, we think it is important for vapers to understand what exactly 510 connectors are and how they work.
As with everything else in life, if you understand how something works, it will be easier to diagnose problems that your device may have and fix them without going to a vape shop. We'll look at how 510 connectors are made and the best way to care for them so you can use them without too many headaches
Why is it called the 510 connector?
The 510s got their name from the length of the connector, 5 mm and 10 threads. When you look at the bottom of your tank or atomizer, you will only see the outer (male) portion of the 510 connector. The internal, receiving part (female connection) of the 510 is inserted into your mod and only then, when they are twisted together, are they technically a whole 510.
How does the 510 connector work?
On each part of the 510, external and internal, you will see corresponding parts. And although each part has only 3 sections, each of them solves its own problem.
The deepest part of any 510 is the small pin that acts as the positive pin for the circuit. The pins can be threaded, plug-in or spring-loaded, and essentially they do the same job, which is to allow current to flow from the batteries to the mod and on to the atomizer.
The part surrounding the center pin is insulation. If the insulation cannot separate the positive and negative contacts, the risk of a short circuit will be very high. This small part of your vape mod is one of the most important parts when it comes to safety and most often overlooked.
Replacing the evaporator
If the steam generator begins to produce a low amount of steam or its taste does not bring you pleasure, then one of the reasons for this may be replacing the evaporator. It, like any structural part, has its own service life.
The force of blowing on the evaporator can be achieved using a silicone ring with slots, by rotating which you can make the holes on the air duct larger or smaller, changing the depth of tightening.
To replace it, you need to unscrew the battery from the clearomizer, then disconnect the tank.
Other options for unscrewing the tank
Thanks to special substances, it is possible to disconnect the atomizer from the base or the tank from the evaporator. In the process of active vaping, so-called gars are formed inside. Because of them, the components of the liquid boil, which settle tightly on the thread and do not solidify.
WD-40 is a substance that is sold at hardware stores. This composition must be dripped onto the thread through the air duct or hole for vaping the puff. Then you need to wait 5-10 minutes for the plaque to dissolve. Then rinse the vape to remove any remaining WD-40. The mobility of parts is guaranteed to increase.
Glass is the most vulnerable element of e-cigarettes. Owners of rare devices purchased from AliExpress or other foreign online stores have long been convinced of this. Components for new devices are rare in stationary vape shops.
It is impossible to repair cracked glass. In addition, with constant unscrewing/twisting, the crack only increases in volume. To avoid the cost of purchasing a new electronic device, it is more rational to clean your device after every 2-3 refills.
If the tank on an electronic cigarette does not unscrew
Experienced vapers recommend several solutions in such cases:
- if the base scrolls, “stop” it with any object that fits into the hole in the air duct and unscrew the tank;
- A rubberized mat and rubber gloves will help you remove the drip type, which will prevent the part from turning in your hands;
- wrap the glass vessel with electrical tape or plaster to avoid scratches and use pliers.
This must be done carefully so as not to damage the metal parts or crush the glass.
Instructions for unscrewing the tank
If the tank does not unscrew, then the problem is solved by performing the following manipulations:
- Stop the base without applying any force, as the glass may crack and will not be suitable for further use. Make this with some thin object that will fit into the air vent. This way you will fix the body;
- Using rubber gloves or a thin rubber mat, unscrew the evaporator, glass or drip tip so that your fingers do not roll over the body of the device;
- Wrap the glass in a couple of layers with electrical tape or adhesive tape so that the glass is not deformed with pliers if you are unable to remove the clearomizer by hand;
- Use a wet cloth/thin stream from the tap to rinse the joints and clean the threads. If there are no liquid residues on the fasteners, then everything was done correctly. It is better not to refuel the e-cigar while unwinding the tank;
- Unscrew the remaining parts and wash them thoroughly;
- Install the glass several times, clean parts will not leak.
Terms of use
Follow all rules for operating, refueling, assembling and disassembling your steam generator
- avoid contact of the cigarette with water;
- use only for its intended purpose;
- protect from temperature changes and open fire;
- disassembling the box mod will void the manufacturer's warranty.
Monitor the amount of fluid and timely and competent replacement. Have a nice couple!
Istick 20. The thread is broken. Option to solve the problem.
Is the tank not spinning up on the Eleaf Ijust S? Break him to *** with the help of my advice
