First aid if a hookah burns through carpet, linoleum, parquet

• home
• Articles
• What to do if you burn the carpet

Carpet flooring is a popular attribute of any interior. They create an atmosphere of comfort, insulate the floor, dampen extraneous sounds and make the environment complete. Unfortunately, carpet owners have to deal with damage from time to time, which inevitably occurs during use and requires repair. It can be:

• cuts;
• burns;
• loss of color;
• bald patches in places where the pile is abraded.

Carpet pile can melt or burn due to heat exposure. There is no need to throw away and replace this coating with a new one. There are several methods that are simple and accessible to anyone who wants to repair the damaged area themselves. From our article you will learn how to restore a burnt carpet.

How to remove a burn mark on a countertop?

Mix a small amount of baking soda and water and apply directly to the stain. Use a sponge and gently work the mixture over the surface for a few minutes. Finish by wiping off excess with a clean, soft cloth.

Interesting materials:

What does a stepper machine train? Stepper machine how to use? What is insurance premium in the loan amount? What is consolidated enforcement proceedings against a debtor? Tamoxifen what is it? What is craving? What is thiamine mononitrate? What are three lines on the wrist? How to take True mass? What is citrulline?

If you burn the carpet

Often this type of flooring is still found in apartments. And often the models and qualities of carpets fit so well into the interior that you simply don’t want to change them. What to do if charcoal burns the carpet with hookah charcoal? Don't panic, but restore.

Required Tools

In order to hide the incident, you will need:

1. carpet cleaner;
2. nail scissors;
3. transparent glue;
4. a brush with stiff bristles.

Patch

A large piece of damaged carpet can only be replaced with a patch. To do this, you need to cut off the damaged piece using scissors. And glue a part of the same size and color in place of the formed hole.

Important: the patch is glued directly to the floor using double-sided tape or glue.

Fiber extension method

This method is only suitable if the coal marks are small. To begin, carefully cut out the charred fibers with scissors. The base of the carpet must be left untouched. Then the resulting hole is filled with transparent glue. And whole fibers are cut off from the carpet in hidden places. Hidden places on the carpet can be where some furniture is, or small areas that are not obvious. After the glue has dried a little, fill the hole with new fibers.

The essence of the problem

In the wild, which is how most people like to relax, especially burns become a common problem. After all, tourists usually have to deal with fire: cook simple food, or warm themselves near a fire. It is the fire that becomes a means of increased danger, because sparks flying from the fire can get on the skin and cause burns of varying degrees of complexity. But it’s much worse if such sparks fall on clothing (especially made of synthetic materials): it can instantly flare up and begin to melt. In such a situation, the matter may result in more serious consequences.

If such a disaster suddenly occurs, then without regret, the clothes must be immediately removed (in extreme cases, simply torn) so that the flame does not touch the body. It must be remembered that fresh air should not come into contact with the fire: it is best to throw a thick blanket over the victim. Cold water will help to significantly reduce pain: just water the burn area with clean, running water. But under no circumstances should you lubricate burns with any fat, or pour urine on them (as some advise), as well as open the blisters that have formed at the site of damage. This can not only aggravate the situation, but also introduce dirt into the wound. So what should you do if you get injured from a fire?

Read also: Boiled beet salads

A few recommendations

If the owners of the apartment do not want to repair the carpet, then you can hide the damaged area by rearranging the furniture, simply covering it with some object. During repairs, you need to take into account that the patch may have slight differences in color.

Related links: Basic rules for arranging a balcony

Since the carpet was exposed to ultraviolet radiation during use, or lost color during the cleaning process, etc. To summarize, we can say that the process of repairing this coating is quite simple. Therefore, after damage, you should not immediately throw it away.

Treatment and first aid for burns of the foot and heel

A burn to the foot or heel is quite rare in medical practice, because in most cases the foot is protected by shoes, so the degree of damage is low. However, such burns occur in isolated cases. Burns of the foot or heel can be thermal, chemical, radiation, or electrical.

• A thermal burn occurs as a result of the interaction of elevated temperatures on the area of ​​the foot or heel (burn with boiling water, flame, steam, hot objects).
• Chemical damage occurs as a result of exposure of the skin surface to pesticides and other harmful chemicals (burn with acid, alkali).
• A radiation burn to the foot or heel occurs after exposure of the lower extremity to radiation substances.
• Electrical injury occurs when an electric current is applied to the leg.

Burnt through the laminate. What to do?

Those who like to smoke a hookah, a cigarette, or burn incense (you can continue the list yourself) often inadvertently drop hot coals onto the surface of the laminate.

Depending on the class and degree of protection of the top layer, as well as on the length of time the coal remains on the surface, there may be varying degrees of damage.

If this is a household laminate of class 31-32 with a thin layer of protection (up to 0.3 mm) of polyurethane varnish, then it will burn through quickly enough and damage will affect the printed layer with the pattern.

In this review we will tell you how you can save laminate flooring from damage and restore its surface.

How to repair small areas

First of all, it is necessary to trim off the burnt fibers. To do this, it is convenient to use sharp manicure scissors. Then, using tweezers, remove these fibers. Next you will need some intact fibers. They can be found in an area of ​​the carpet that is less noticeable. Nail scissors will also come to the rescue here. Next, you should place clean fibers in a suitable container and make sure that there will be enough of them for repair.

Related links: How to bleach white clothes at home

Next, you need to apply a strong adhesive to the hole in the coating and apply clean fibers using tweezers. After the manipulations, it is necessary that everything attaches well. To do this, this place needs to be covered with some object for several days. It could be a stack of books. After removing the book from the area that was repaired, you should comb out the lint using a fine-tooth comb.

If you burn the parquet

But what should you do if you burn through the parquet with a hookah? Options for saving parquet flooring from traces of coal from a hookah also depend on their degree.

Sanding and masking

The easiest way, in which there is no need to pay attention to the entire coating. To mask holes in the parquet caused by hookah coal, the following works well:

1.Epoxy resin and color to match the color of the parquet. By mixing the ingredients you can get a solution of the perfect color. Carefully fill the hole in the parquet with the mixture.

Important: cover the burnt area as evenly as possible, since after drying the resin is difficult to level;

2.Hard wax. In construction stores it is easy to choose the wax of the desired shade. Under the influence of high temperature it must be melted and poured into the hole on the coating. After drying, the excess is sanded off and the area of ​​the floor that is being restored is coated with a special varnish.

Looping

Using a special apparatus, the top layer of parquet is removed. Next, using putty, the holes and joints between the parquet boards are sealed. Afterwards, any irregularities that appear are sanded and the parquet is varnished.

This restoration method is used for severe visible damage to the coating.

If you burn linoleum with a hookah

Linoleum is even now the most commonly used flooring method. Justified, because it has its own advantages. And if it is often found in ordinary apartments, then it is also necessary to answer the question: how to restore linoleum if it was burned by fallen coal from a hookah. In this situation, everything depends on the degree of burn-through. Let's look at each in more detail.

Damage to the top layer

The top layer refers to a thin protective film.

If it is damaged, it is enough to clean the damaged area, and shade the edges of the hole with a regular coin (edge).

Afterwards, the damaged area can be treated with linoleum mastic, which is sold in hardware stores.

Damage to the coating base

In this case, not only the design deteriorates, but also the foam base of the coating. Such a defect certainly catches the eye. There are two ways to correct the situation:

1. You will need cold welding glue type C (it is suitable for welding old linoleum) and a pigment that matches the color of the coating. The two components are mixed, and the hole is filled with the resulting composition. After the mixture has dried, its upper part is removed so that the linoleum coating remains smooth: you can cut off excess glue with a sharp knife. Upon completion of the restoration, it is recommended to rub the linoleum with special wax.
2. Using mastic and a piece of damaged linoleum. A small part of the coating must be cut off in a hidden place. Using a sharp knife, scrape off the top colored layer into the mastic. Fill the hole with the resulting mixture. The excess is also cut off with a knife, and the entire surface is treated with wax.

Burning through

Such burnout can only be restored with a patch. It can be picked up or cut out from hidden places. Having lifted the linoleum, the area around the hole is covered with double-sided tape. And a patch is glued to the floor, which is ideal in size and color. Afterwards the joint is treated with type C glue.

If it is difficult to find a patch of a suitable color, then you can approach the problem with creativity.

And fill the hole with a kind of applique.

Important: after gluing the works of creativity, it is necessary to treat the coating with a special varnish.

No need to throw it away

We were annoyed: the burn from the cigarette butt turned out to be large in area, and it seemed to me that the carpet was now on its way to the trash heap. However, we remembered our old friend who faced a similar problem.

We've had to spend money on carpet repairs before, it's not cheap, but he suggested a fairly simple method. It turns out that you can fix a carpet using simple tools and whatever you have lying around at home.

Procedure:

1. Remove the coal immediately using fire-resistant objects (metal scoop, thick, damp cloth).
2. Clean the damaged area by removing coal dust and burnt fragments of the coating. This can be done carefully, for example, with sandpaper.
3. Cover the edges of the laminate with masking tape. This is necessary so that the particles of the reducing compounds do not stain the rest of the surface.
4. Find a caulking product from the manufacturer of your coating. If this is not possible, look for an analogue. As a rule, all major manufacturers, such as Quick-Step, Pergo or Tarkett, offer restoration products.
5. Add a little color of the required shade to the putty. Apply the putty using a small putty knife.
6. Wait until dry and remove the masking tape.

This method is acceptable if the damage is not too extensive. If the damage to the surface is wider, it will be more difficult to hide the burnt area with putty.

Restoration of joints

A poorly taped seam between the canvases may come apart. If there is a discrepancy near doors, under furniture or along a wall, the defect is easily covered with a decorative threshold. In the center of the room it is better to use cold or hot welding.

Hot is done only by professionals (you need skills and a hot air gun). The technician heats up the PVC cord and places it in the joint.

Cold welding is relevant in everyday life: